061: Tape Echo; 062: Auto Reverse - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

061: Tape Echo

This effect simulates a tape echo unit with three playback
heads. The distortion and tonal change typical of magnetic
tape are also reproduced.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
Feedback Amt
+
Tape
Saturation
Trim
Pre Tone
High / Low Damp
Wah Flatter
Right
D
-mod
Delay Time
Delay (Tap1)
Sets the delay time (tap1)
0...2700
[msec]
Selects the modulation source
a
Src
Off...Tempo
of the delay time
–2700...
Sets the modulation amount of
Amt
+2700
delay time
Sets the position of Tap 2
b Tap2
relative to the Tap 1 delay time
0...100
Position [%]
the depth of pitch variation
Sets the position of Tap 3
Tap3
relative to the Tap 1 delay time
c
0...100
Position [%]
the depth of pitch variation
Tap1 Level
0...100
Sets the Tap1 output level
Pan
L, 1...99, R
Sets the stereo image of tap1
d
Sets the Tap1 feedback amount
FB Amt
–100...+100
Tap2 Level
0...100
Sets the Tap2 output level
Pan
L, 1...99, R
Sets the stereo image of tap2
e
Sets the Tap2 feedback amount
FB Amt
–100...+100
Tap3 Level
0...100
Sets the Tap3 output level
Pan
L, 1...99, R
Sets the stereo image of tap3
f
Sets the Tap3 feedback amount
FB Amt
–100...+100
Sets the amount of feedback
Feedback
0...100
for Taps 1, 2, and 3
g
Selects the modulation source
Src
Off...Tempo
of feedback amount
Amt
–100...+100
Sets the feedback amount
High Damp
Sets the damping amount in
0...100
[%]
the high range
h
Low Damp
Sets the damping amount in
0...100
[%]
the low range
i
Saturation
0...100
Sets the distortion amount
Input Trim
0...100
Sets the input gain
j
Pre Tone
0...100
Sets the tone of the input
Wow Flutter
Sets the frequency at which
0.02...1.00
[Hz]
pitch variation will occur
k
Wow Flutter
Sets the depth of pitch
0...100
depth
variation
Dry,
Sets the balance between the
Wet/Dry
1 : 99...99 : 1,
effect and the dry input
Wet
l
Selects a modulation source for
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
a: Delay (Tap1) [msec]
a: Src
a: Amt
b: Tap2 Position [%]
b: Tap3 Position [%]
The delay time for Tap 2 and 3 is specified as a proportion
(%) relative to Delay (Tap1). Even if you use dynamic
modulation to control Delay (Tap1), Tap 2 and 3 will change
at the same proportion.
Wet / Dry
(3)
(2)
(1)
Level
Pan
Delay
Tap2/3
Position
Wet / Dry
p.329
p.329
p.329
p.329
p.329
p.329
p.329
p.329
p.329
d: FB Amt
e: FB Amt
f: FB Amt
g: Feedback
The feedback output from Tap 1, 2, and 3 is mixed according
to the FB Amt, and then the final amount of feedback is
specified by Feedback.

062: Auto Reverse

This effect records the input signal and automatically plays
it in reverse (the effect is similar to a tape reverse sound).
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Auto Reverse
Rec/Reverse Play
Control
Right
D-mod
D
-mod
Envelope Control
Input
Envelope Select
Single, Multi Sets the recording mode
a
Rec Mode
b Reverse Time
Sets the maximum duration of
20...2640
[msec]
the reverse playback
Selects whether the start and
Envelope
D-mod,
end of recording is controlled
Select
Input
via the modulation source or
the input signal level
c
Selects the modulation source
that controls recording when
Src
Off...Tempo
Envelope Select is set to D-mod
Sets the recording start level
d Threshold
0...100
when Envelope Select is set to
Input
Sets the speed of the response
e Response
0...100
to the end of recording
Always On,
Selects how a dry sound is
f
Direct Mix
Always Off,
mixed
Cross Fade
Dry, 1 : 99...
Sets the balance between the
Wet/Dry
99 : 1, Wet
effect and the dry input
Selects a modulation source for
g
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
a: Rec Mode
b: Reverse Time [msec]
When Rec Mode is set to Single, you can set up to 2,640msec
for Reverse Time. If recording starts during the reverse
playback, the playback will be interrupted.
When Rec Mode is set to Multi, you can make another
recording during the reverse playback. However, the
maximum Reverse Time is limited to 1,320msec.
If you wish to record a phrase or rhythm pattern, set Rec
Mode to Single. If you record only one note, set Rec Mode
to Multi.
The Reverse Time parameter specifies the maximum
duration of the reverse playback. The part in excess of this
limit will not be played in reverse. If you wish to add short
pieces of the reverse playback of single notes, make the
Reverse Time shorter.
Delay
Wet / Dry
Direct
Mix
Wet / Dry
p.329
p.329
p.330
p.330
p.330
p.317
p.317
329

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents