KORG M50-88 Parameter Manual: Tone Adjust

M50 music workstation.
Hide thumbs
   
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419

Advertisement

Program mode
▼0–5: Menu Command
• 0: Write Program ☞p.73
• 1: Exclusive Solo ☞p.73
• 2: Copy Arpeggiator ☞p.75
For more information, please see "Program: Menu
Command" on page 73.
6
0–7: Tone Adjust
0–7a
0–7b
0–7c
The Tone Adjust function assigns important program
parameters and easy-edit parameters to the switches and
sliders in the display for quick edits of selected parameters.
Tip: In Combination and Sequencer modes, Tone Adjust also
lets you edit Program parameters without the need to save a
different version of the original Program. For more
information on Tone Adjust in these modes, please see
"Tone Adjust" on page 85 and page 135.
Absolute (Abs), Relative (Rel), Meta parameter
There are three kinds of Tone Adjust parameters: Absolute,
Relative, and Meta.
Absolute parameters usually edit a single Program
parameter, such as Oscillator 1 Drive. The Program and
Tone Adjust parameters mirror one another; when you
change one, the other will change to match.
Relative parameters typically adjust two or more Program
parameters simultaneously. For instance, F/A EG Attack
Time affects a total of six Program parameters. The value of
the Relative parameter shows the amount of change to these
underlying Program parameters.
If the Relative parameter is set to 0 (the slider in the display
is at the center position), the value of the corresponding
program parameter will not change.
The definitions of higher and lower settings can vary,
depending on the specific parameter. Unless noted
otherwise, they work as follows:
When the Relative parameter is at +99 (the maximum), the
Program parameters are all at their maximum as well.
Similarly, when the Relative parameter is at –99 (the
minimum), the Program parameters are at zero.
Relative Tone Adjust parameter scaling
99
Parameter
Value
As Programmed
00
–99
0
Relative Tone Adjust Value
A few of the Program parameters controlled by Relative
Tone Adjust are bipolar, meaning that they can be either
positive or negative (instead of just positive). When these
Program parameters are set to negative values, the Tone
Adjust parameter may behave differently from the
description above.
0–7
Menu
+99

Advertisement

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: