041: Doppler - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

Effect Guide
Dry, 1 :99...
Wet/Dry
99 : 1, Wet
j
Src
Off...Tempo
Amt
–100...+100
a: Control Mode
g: Voice 1: Resonance
i: Voice 2: Resonance
This parameter determines the resonance intensity.
When Control Mode = Manual, the Resonance parameter
sets the intensity of resonance. If the Resonance parameter
has a negative value, harmonics will be changed, and
resonance will occur at a pitch one octave lower.
When Control Mode = LFO, the intensity of resonance
varies according to the LFO. The LFO sways between
positive and negative values, causing resonance to occur
between specified pitches an octave apart in turn.
When Control Mode = D-mod, the resonance is controlled
by the dynamic modulation source. If JS X is assigned as the
modulation source, the pitch an octave higher and lower can
be controlled, similar to when LFO is selected for Control
Mode.
a: LFO/D-mod Invert
When Control Mode = LFO or D-mod, the controlled phase
of either Voice 1 or 2 will be reversed. When the resonance
pitch is set for Voice 1 (Resonance has a positive value),
Voice 2 will resonate at a pitch an octave below (Resonance
has a negative value).
f: Voice 1: Pitch
f: Fine [cents]
h: Voice 2: Pitch
h: Fine [cents]
The Pitch parameter specifies the pitch of resonance by note
name. The Fine parameter allows for fine adjustment in
steps of cents.
g: High Damp [%]
i: High Damp [%]
This sets the amount of damping amount for the high
frequencies of the resonant sound. Lower values create a
metallic sound with a higher range of harmonics.

041: Doppler

This effect simulates the "Doppler effect" of a moving sound
with a changing pitch, similar to the siren of an passing
ambulance. Mixing the effect sound with the dry sound will
create a unique chorus effect.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Right
D
-mod
Trigger
Loop, 1-Shot Switches LFO operation mode
LFO Mode
a
Src
Off...Tempo
b LFO Sync
Off, On
316
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry
Doppler
Pan Depth
LFO
LFO Mode = 1-Shot
p.316
Selects the modulation source
of LFO reset
p.316
Switches between LFO reset on
and off when LFO Mode is set
to Loop
p.316
LFO
Frequency
[Hz]
c
Src
Amt
MIDI Sync
BPM
d
Base Note
Times
LFO Type
e
CmnLFO
Offset [deg]
Pitch Depth
f
Src
Amt
Pan Depth
g
Src
Amt
Wet/Dry
h
Src
Amt
a: LFO Mode
a: Src
b: LFO Sync
The LFO Mode parameter switches LFO operation mode.
When Loop is selected, the Doppler effect will be created
repeatedly. If LFO Sync is set to On, the LFO will be reset
when the modulation source specified with the Src
parameter is turned on.
When LFO Mode is set to 1-Shot, the Doppler effect is
created only once when the modulation source specified in
the Src field is turned on. At this time if you do not set the
Src parameter, the Doppler effect will not be created, and no
effect sound will be output.
The effect is off when a value for the modulation source
specified for the Src parameter is smaller than 64, and
the effect is on when the value is 64 or higher. The
Doppler effect is triggered when the value changes
from 63 or smaller to 64 or higher.
Wet / Dry
f: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes
away. This parameter sets this pitch variation.
g: Pan Depth
Wet / Dry
This parameter sets the width of the stereo image of the
effect sound. With larger values, the sound seems to come
and go from much further away. With positive values, the
sound moves from left to right; with negative values, the
sound moves from right to left.
0.02...20.00
Sets the speed of the LFO p.298
Selects a modulation source for
Off...Tempo
LFO speed
–20.00...
Sets the modulation amount of
+20.00
LFO speed
When this is on, the LFO speed
is set by BPM, Base Note, and
Off, On
Times, instead of Frequency
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
40.00...
manually for this individual
300.00
effect
Selects the type of notes that
...
specify the LFO speed
Sets the number of notes that
x1...x32
specify the LFO speed
Individual,
Selects either (individual) LFO,
Common1,
Common FX LFO1, or Common
Common2
LFO2
Sets the phase offset when
–180...+180
Type = Common 1 or Common
2
Sets the pitch variation of the
0...100
moving sound
Selects the modulation source
Off...Tempo
of pitch variation
Sets the modulation amount of
–100...+100
pitch variation
Sets the panning of the moving
–100...+100
sound
Selects the modulation source
Off...Tempo
of panning
Sets the modulation amount of
–100...+100
panning
Dry,
Sets the balance between the
1 : 99...99 : 1,
effect and the dry input
Wet
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
p.297
p.297
p.297
p.297
p.297
p.297
p.316
p.316

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents