016: Stereo Decimator; 017: St. Analog Record (Stereo Analog Record) - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

016: Stereo Decimator

This effect creates a rough sound like a cheap sampler by
lowering the sampling frequency and data bit length. You
can also simulate noise unique to a sampler (aliasing).
Stereo In - Stereo Out
Left
Pre LPF
Resolution
Decimator
D
-mod
Sampling Frequency
LFO
Decimator
Pre LPF
Resolution
Right
Selects whether the harmonic
noise caused by a decrease in
Pre LPF
Off, On
sampling frequency is
a
generated or not
High Damp
Sets the ratio of cut of the high
0...100
[%]
range
Sampling
1.00k...
Sets the sampling frequency
Freq [Hz]
48.00k
Selects the modulation source
b
Src
Off...Tempo
of the sampling frequency
–48.00k...
Sets the modulation amount of
Amt
+48.00k
the sampling frequency
LFO
Frequency
0.02...20.00
Sets the speed of the LFO
[Hz]
c
Selects a modulation source for
Src
Off...Tempo
LFO speed
–20.00...
Sets the modulation amount of
Amt
+20.00
LFO speed
When this is on, the LFO speed
MIDI Sync
Off, On
is set by BPM, Base Note, and
Times, instead of Frequency
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
BPM
40.00...
manually for this individual
d
300.00
effect
Selects the type of notes that
Base Note
...
specify the LFO speed
Sets the number of notes that
Times
x1...x32
specify the LFO speed
Individual,
Selects either (individual) LFO,
LFO Type
Common1,
Common FX LFO1, or Common
Common2
LFO2
e
Sets the phase offset when
CmnLFO
–180...+180
Type = Common 1 or Common
Offset [deg]
2
Sets the depth of the sampling
Depth
0...100
frequency LFO modulation
Selects the LFO modulation
Src
Off...Tempo
source of the sampling
f
frequency
Sets the LFO modulation
Amt
–100...+100
amount of the sampling
frequency
g Resolution
4...24
Sets the data bit length
Output Level 0...100
Sets the output level
Selects the modulation source
Src
Off...Tempo
h
for the output level
Sets the modulation amount of
Amt
–100...+100
the output level
Dry, 1 : 99...
Sets the balance between the
Wet/Dry
99 : 1, Wet
effect and the dry input
Selects a modulation source for
i
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
a: Pre LPF
If a sampler with a very low sampling frequency receives
very high-pitched sound that could not be heard during
playback, it could generate pitch noise that is unrelated to
the original sound. Set Pre LPF to On to prevent this noise
from being generated.
Wet / Dry
High Damp Output Level
High Damp Output Level
Wet / Dry
p.301
p.297
p.297
p.301
p.301
If you set the Sampling Freq to about 3 kHz and set Pre LPF
to Off, you can create a sound like a ring modulator.
g: Resolution
h: Output Level
If you set a smaller value for the Resolution parameter, the
sound may be distorted. The volume level may also be
changed. Use Output Level to adjust the level.
017: St. Analog Record
(Stereo Analog Record)
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the
modulation caused by a warped turntable.
Stereo In - Stereo Out
Left
EQ Trim
Pre EQ
EQ Trim
Pre EQ
Right
a
Speed [RPM] 33 1/3, 45, 78 Sets the r.p.m. of a record
Sets the modulation depth
b Flutter
0...100
Noise Density 0...100
Sets the noise density
c
Noise Tone
0...100
Sets the noise tone
Noise Level
0...100
Sets the noise level
Selects the modulation source
Src
Off...Tempo
d
for the noise level
Sets the modulation amount of
Amt
–100...+100
the noise level
Sets the click noise level
Click Level
0...100
Selects the modulation source
e
Src
Off...Tempo
for the click noise level
Sets the modulation amount of
Amt
–100...+100
the click noise level
f
EQ Trim
0...100
Sets the EQ input level
Pre EQ Cutoff
300...10.00k
Sets the EQ center frequency
[Hz]
g
Q
0.5...10.0
Sets the EQ band width
Gain [dB]
–18.0...+18.0 Sets the EQ gain
Dry, 1 : 99...
Sets the balance between the
Wet/Dry
99 : 1, Wet
effect and the dry input
Selects a modulation source for
h
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
b: Flutter
This parameter enables you to set the depth of the
modulation caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise
that occurs once every rotation of the turntable. This
simulation reproduces record noise, and the noise generated
after the music on a vinyl record finishes.
EQ and Filters (EQ/Filter)
Wet / Dry
Analog Record
Simulation
Wet / Dry
p.301
p.301
301

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents