KORG M50-88 Parameter Manual: Insert Effects (ifx1–ifx5); In/out

M50 music workstation.
Hide thumbs
   
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419

Advertisement

Effect Guide
Insert Effects (IFX1–IFX5)
In/Out
Insert Effects (IFX 1–5) have a stereo input and a stereo
output. If you set the Wet/Dry parameter to Dry (no effect),
the input signal will be passed through, in stereo, without
being processed by the effect. If you select Wet (effect
applied), the processed signal will be output in one of the
following ways:
Mono In - Mono Out
Wet
Mono In - Stereo Out
Stereo In - Stereo Out
Mono–Mono Parallel Effects
109: P4EQ // P4EQ —153: BPM Dl // BPM Dl
Mono In/Out Effect
Mono In/Out Effect
These effects are typically stereo-in/stereo-out, but they
have a special structure. The L channel and R channel of the
stereo input each have their own independent mono effect.
Each mono output can then be panned to the desired
position in the stereo field.
• Track1: Piano, Pan=L001, Bus (IFX/Output) Select=IFX1
• Track2: E.Piano, Pan=R127, Bus (IFX/Output)
Select=IFX1
So that you don't mix the sound of the two tracks that are
being input, set the P0: Play/REC Pan parameter to L001
and R127 respectively.
Example: IFX1: 116: P4EQ // Phaser
Track 1: Piano is sent to the L channel P4EQ, and Track 2:
E.Piano is sent to the R channel Phaser. Use the P8: IFX–
IFX1 page Pan parameter to set the output position of each
sound. In this example, both are set to C064. See the diagram
below.
IFX1: 116: P4EQ // Phaser
Input/output variations for each effect are shown in upper
left of the block diagrams starting on page 356.
If you select 000: No Effect, stereo input signals are output
in stereo without being processed.
Pressing the On/Off button of IFX1–IFX5 in the P8:IFX–
Insert FX Setup pages in each mode will toggle between On
276
+
Effect
+
Effect
Effect
Effect
Pan
Pan
and Off. When Off is selected, the effect will be bypassed,
and the stereo input signal will be output in stereo without
being processed.
The M50 can also turn IFX1–IFX5 off separately from
the setting of the On/Off button by receiving MIDI
control change message CC#92. Value 0 will turn them
off, and value 1–127 will turn them on.
You can also use "Effect Global SW" (Global 0–1b) to
turn IFX1–5 on and off. This MIDI control is performed
on the global MIDI channel (Global 1–1a).
Double-size effects
Double-size effects (154: St.Mltband Limiter – 170: Early
Reflections) use twice as much space as other effects.
You can use double-size effects for insert effects IFX1–IFX4
and master effect MFX1. However, the effect of the number
that follows it will be unavailable. For example if you've
selected a double-size effect for IFX1, you won't be able to
use IFX2. If you've selected a double-size effect for MFX1,
you won't be able to use MFX2.
An example of when a double-size effect is selected for IFX1 and IFX4

Advertisement

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: