167: Hold Delay - Korg M50-88 Parameter Manual

Effect Guide

167: Hold Delay

This effect records the input signal and plays it back
repeatedly. You can control the start of recording and reset
via a modulation source. Easy to use for real-time
performances.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Right
D -mod
REC Control
D -mod
RST Control
Loop Time Auto,
a
[msec] 1...10800
b Loop BPM
Off, On
Sync
MIDI,
BPM 40.00...
300.00
c
Time Over? ---, OVER!
Loop Base
...
Note
d
Times x1...x32
e REC Control
Off...Tempo
Src
RST Control
f Off...Tempo
Src
Manual REC REC Off,
g
Control REC On
Manual RST
h Off, RESET
Control
L100...L1, C,
Pan
R1...R100
i Src Off...Tempo
Amt –100...+100
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
j Src Off...Tempo
Amt –100...+100
a: Loop Time [msec]
With Auto, the loop time is automatically set. Otherwise,
you can specify the loop time.
When Auto is selected, the Loop Time is automatically set to
the time it takes for a performance recorded while the
Modulation Source or Manual REC Control is on. However,
if the time length exceeds 10,800msec, the loop time will be
automatically set to 10,800msec.
c: Time Over?
You can set the delay time up to 10,800msec. If the delay
time exceeds this limit, the error message "OVER!" appears
in the display. Set the delay time parameters so that this
message will not appear. Time Over? is only a display
parameter.
370
Delay
Pan
Loop Time: Auto/ ...5400ms
Tempo
BPM
Base Note x Times
BPM
Sets Automatic loop time setup
mode or specifies loop time
p.370
Specifies whether delay time is
set in milliseconds, or as a note
value relative to tempo p.370
MIDI syncs to the system
tempo; 40–300 sets the tempo
manually for this individual
effect p.370
An error indication that appears
if delay time exceeds the upper
limit when MIDI/Tempo
Sync=On
Selects the type of notes to
specify the delay time p.370
Sets the number of notes to
specify the delay time p.370
Selects control source for
recording p.370
Selects control source for reset
p.370
Sets the recording switch
p.370
Sets the reset switch p.370
Sets the stereo image of the
effect
Selects the modulation source
of stereo image of the effect
Sets the modulation amount of
stereo image of the effect
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry
b: Loop BPM Sync
c: BPM
d: Loop Base Note
d: Times
If Loop BPM Sync is on, the Times setting is ignored; the
loop time is determined by BPM, Loop Base Note, and
Times. Even in this case, the delay time cannot exceed
10,800 msec.
"Hold" procedure (when Loop Time = Auto)
Wet / Dry
1. "Rec Src" JS +Y: #01
"Reset Src" JS –Y: #02
"Manual REC Control" REC Off
"Manual RST Control" RESET
"Loop Time [msec]" Auto
"MIDI/Tempo Sync" Off
Wet / Dry
It should be noted that all recordings will be deleted
while Reset is On.
2. "Manual RST Control" Off
Reset is cancelled and the unit enters Rec ready mode.
3. Push the joystick in the +Y direction (forward) and play a
phrase you wish to hold. When you pull the joystick to
its original position, the recording will be finished and
the phrase you just played will be held.
Loop Time is automatically set only for the first recording
after resetting. If the time length exceeds 10,800msec,
Loop Time will be automatically set to 10,800msec. (If
you have set Times to 1–10,800msec, the specified loop
time will be used regardless of the time taken from push-
ing the joystick forward until it is pulled back. However,
the recording method remains the same. The phrase
being played while the joystick is pushed forward will be
held.)
4. If you made a mistake during recording, pull the joystick
in the –Y direction (back) to reset. In this way, the
recording will be erased. Repeat step 3. again.
5. The recorded phrase will be repeated again and again.
You can use this to create an accompaniment.
6. By pushing the joystick in the +Y direction (forward),
you can also overdub performances over the phrase that
is being held.
e: REC Control Src
g: Manual REC Control
REC Control Src selects the modulation source that controls
recording.
If this modulation is on, or if Manual REC Control is set to
On, you can record the input signal. If a recording has
already been carried out, additional signals will be
overdubbed.
The effect is off when a value for the modulation source
specified for the REC Control Src parameter is 63 or
smaller, and the effect is on when the value is 64 or
higher.
f: RST Control Src
h: Manual RST Control
The RST Control Src parameter specifies the modulation
source that controls the reset operation.
When you set this modulation source to On, or Manual RST
Control to RESET, you can erase what you recorded. If the
Loop Time parameter has been set to Auto, the loop time is
also reset.
The effect is off when a value for the modulation source
specified for the RST Control Src parameter is 63 or
smaller, and the effect is on when the value is 64 or
higher.