Tap4 (240)
Sets the Tap4 (LFO phase=240
0...2000
[msec]
degrees) delay time
Depth
0...30
Sets the Tap4 chorus depth
Always On,
e
Always Off,
Selects on, off, or modulation
On➝Off
source for the control of Tap4
Status
(Dm),
output
Off➝On
(Dm)
Tap5 (120)
Sets the Tap5 (LFO phase=120
0...2000
[msec]
degrees) delay time
Depth
0...30
Sets the Tap5 chorus depth
Always On,
f
Always Off,
Selects on, off, or modulation
On➝Off
source for the control of Tap5
Status
(Dm),
output
Off➝On
(Dm)
Tap6 (300)
Sets the Tap1 (LFO phase=300
0...2000
[msec]
degrees) delay time
Depth
0...30
Sets the Tap6 chorus depth
Always On,
g
Always Off,
Selects on, off, or modulation
On➝Off
source for the control of Tap6
Status
(Dm),
output
Off➝On
(Dm)
1 : L 1 2 3 4 5 6 R,
Selects the stereo panning
h Panning
2 : L 135 246 R,
pattern for each tap
Preset
3 : L 1 3 5 2 4 6 R,
4 : L 1 4 5 6 3 2 R
Tap1
–100...+100
Sets the Tap1 feedback amount
Feedback
Selects the modulation source
for the Tap output level,
i
Src
Off...Tempo
feedback amount, and effect
balance
Sets the modulation amount of
Amt
–100...+100
Tap1 feedback amount
Dry, 1 : 99...
Sets the balance between the
Wet/Dry
99 : 1, Wet
effect and the dry input
Selects a modulation source for
j
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
b, c, d, e, f, g: Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (dm): Output level is switched from on to off
depending on the modulation source.
Off→On (dm): Output level is switched from off to on
depending on the modulation source.
Combining these parameters, you can change from 4-phase
chorus to two-tap delay by crossfading them gradually via
the modulation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the
tap outputs.
162: St. Pitch Shifter
(Stereo Pitch Shifter)
This is a stereo pitch shifter. The pitch shift amount for the
p.367
left and right channels can be reversed from each other.
Stereo In - Stereo Out
Left
Input Level
Input Level
p.367
Right
Mode
a
p.367
L/R Pitch
Pitch Shift
[1/2tone]
p.367
b
Src
Amt
Fine [cents]
c
Amt
d L Delay
[msec]
e R Delay
[msec]
Feedback
f
High Damp
[%]
Feedback
Position
g
Spread
Input Level
Dmod [%]
h
Src
Wet/Dry
i
Src
Amt
a: L/R Pitch
When you select Up/Down for this parameter, the pitch
shift amount for the right channel will be reversed. If the
pitch shift amount is positive, the pitch of the left channel is
raised, and the pitch of the right channel is lowered.
High Damp
Pitch Shifter
Delay
Post
Pre
Feedback Position
Feedback
Spread
Pre
Post
Pitch Shifter
Delay
High Damp
Slow,
Switches Pitch Shifter mode
Medium,
Fast
Determines whether or not the
Normal,
L/R pitch shift amount is
Up/Down
inverted
Sets the pitch shift amount in
–24...+24
steps of a semitone
Selects the modulation source
Off...Tempo
of pitch shift amount
Sets the modulation amount of
–24...+24
pitch shift amount
Sets the pitch shift amount in
–100...+100
steps of one cent
Sets the modulation amount of
–100...+100
pitch shift amount
Sets the delay time for the left
0...2000
channel
Sets the delay time for the right
0...2000
channel
Sets the feedback amount
–100...+100
Sets the damping amount in
0...100
the high range
Switches the feedback
Pre, Post
connection
Sets the width of the stereo
–100...+100
image of the effect sound
Sets the modulation amount of
–100...+100
the input level
Selects the modulation source
Off...Tempo
for the input level
Dry, 1 : 99...
Sets the balance between the
99 : 1, Wet
effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
Double Size
Wet / Dry
Wet / Dry
p.324
p.367
p.322
p.322
p.322
p.322
p.322
p.322
p.322
p.325
p.321
p.321
367