049: Detune - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

Fixed
Sets the oscillator frequency
Frequency
0...12.00k
when OSC Mode is set to Fixed
[Hz]
Selects the modulation source
b
Src
Off...Tempo
for the oscillator frequency
when OSC Mode is set to Fixed
Sets the modulation amount of
–12.00k...
Amt
the oscillator frequency when
+12.00k
OSC Mode is set to Fixed
Sets the pitch difference from the
original note when OSC Mode is
Note Offset
–48...+48
set to Note (Key Follow)
c
Fine-adjusts the oscillator
Note Fine
–100...+100
frequency
Direct signal (after passing
through the pre-low-pass filter)
d Direct Mix
0...100
mixed into the ring modulation
output
LFO
Frequency
0.02...20.00
Sets the speed of the LFO p.298
[Hz]
d
Selects a modulation source for
Src
Off...Tempo
LFO speed
–20.00...
Sets the modulation amount of
Amt
+20.00
LFO speed
When this is on, the LFO speed
is set by BPM, Base Note, and
MIDI Sync
Off, On
Times, instead of Frequency
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
BPM
40.00...
e
manually for this individual
300.00
effect
Selects the type of notes that
Base Note
...
specify the LFO speed
Sets the number of notes that
Times
x1...x32
specify the LFO speed
Individual,
Selects either (individual) LFO,
LFO Type
Common1,
Common FX LFO1, or Common
Common2
LFO2
f
Sets the phase offset when
CmnLFO
–180...+180
Type = Common 1 or Common
Offset [deg]
2
Sets the depth of LFO
LFO Depth
0...100
modulation for the oscillator
frequency
g
Selects the modulation source
Src
Off...Tempo
of the depth of modulation
Sets the modulation amount of
Amt
–100...+100
the depth of modulation
Dry,
Sets the balance between the
Wet/Dry
1 : 99...99 : 1,
effect and the dry input
Wet
h
Selects a modulation source for
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
a: OSC Mode
This parameter determines whether or not the oscillator
frequency follows the note number.
a: Pre LPF
This parameter enables you to set the damping amount of
the high range sound input to the ring modulator. If the
input sound contains lots of harmonics, the effect may
sound dirty. In this case, cut a certain amount of high range.
b: Fixed Frequency [Hz]
This parameter sets the oscillator frequency when OSC
Mode is set to Fixed.
c: Note Offset
c: Note Fine
These parameters for the oscillator are used when OSC
Mode is set to Note (Key Follow). The Note Offset sets the
pitch difference from the original note in semitone steps.
The Note Fine parameter fine-adjusts the pitch in cent steps.
Matching the oscillator frequency with the note number
produces a ring modulation effect in the correct key.
Modulation and Pitch Shift (Mod./P.Shift)

049: Detune

p.321
Using this effect, you can obtain a detune effect that offsets
the pitch of the effect sound slightly from the pitch of the
input signal. Compared to the chorus effect, a more natural
sound thickness will be created.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
p.321
Input Level
p.321
+
Input Level
Right
Pitch Shift
[cents]
a
Src
Amt
b Delay Time
p.297
[msec]
Feedback
c
High Damp
[%]
p.297
Input Level
Dmod [%]
p.297
d
Src
p.297
Wet/Dry
p.297
e
Src
Amt
p.297
d: Input Level Dmod [%]
d: Src
This parameter sets the dynamic modulation of the input
level.
Input Level
x1.0
x0.5
Zero
High Damp
Detune
Delay
Feedback
Sets the pitch difference from
–100...+100
the input signal
Selects a modulation source for
Off...Tempo
pitch shift
Sets the modulation amount
–100...+100
for pitch shift
0...1000
Sets the delay time
–100...+100
Sets the feedback amount
Sets the damping amount in
0...100
the high range
Sets the modulation amount of
–100...+100
the input level
Selects the modulation source
Off...Tempo
for the input level
Dry, 1 : 99...
Sets the balance between the
99 : 1, Wet
effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
Input Level
x1.0
Input Level Dmod= +50
Input Level Dmod= +100
x0.5
D
-mod
Higher
Higher
Max
Zero
Wet / Dry
Wet / Dry
p.321
p.321
Input Level Dmod
Input Level Dmod= –50
Input Level Dmod= –100
D
-mod
Max
321

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents