Seq P2: Eq; 2-1: Trim T01-08, 2-2: Trim T09-16 - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

SEQ P2: EQ

2–1: Trim T01–08,
2–2: Trim T09–16
2–1a
2–1b
2–1c
Here, you can set the signal level that enters the EQ of tracks
1–8 and 9–16.
2–1(2)a: Track Select, Tempo, RPPR
Track Select
[Track01...16, Master Track]
(Tempo)
RPPR
Here, you can select the track, specify the tempo that will
control the arpeggiator etc., and turn RPPR on/off.
For more information, please see "0–1–1(2)a: Location,
Meter, Tempo, Tempo Mode, Song Select, Track Select, Reso,
RPPR" on page 129.
2–1(2)b: Track Info
For more information, please see "0–1–1(2)b: Track Program
Select" on page 131.
2–1(2)c: Trim
Track 01 (Track Number):
Auto Load Prog EQ
When you first load a Program into a Track, this parameter
determines whether or not the Program's EQ settings will be
loaded as well.
Once the Program has been loaded, you can change any or
all of the EQ settings as desired. All such edits are stored in
the Song, without affecting the original Program.
Regardless of this setting, subsequent edits to the Program's
EQ in Program mode will not affect the Song.
On: the Program's EQ settings will be loaded automatically
along with the Program. This is the default setting.
Off: the Program's EQ settings won't be loaded. Use this if
you've set up the EQ in a specific way, and then want it to
stay unchanged while you try out different Programs.
Bypass
If this is On (checked), all of the EQ will be disabled,
including Input Trim. Bypass can be convenient for
comparing the results of the EQ with the original signal.
2–1
Menu
[040.00...300.00, EXT]
[Off, On]
[Off, On]
[Off, On]
SEQ P2: EQ 2–1: Trim T01–08, 2–2: Trim T09–16
Input Trim
This controls the volume level going into the EQ. Note that
this parameter uses a linear scale; 50 is equivalent to –6 dB,
25 is the same as –12 dB, and so on.
High settings of the Low, Mid, and High Gain (Seq 2–3(4)a)
controls can cause substantial increases in the overall level.
You can compensate for this by turning down the input trim.
Track 02...08, 09...16 (Track Number):
Here, you can set the parameters for MIDI tracks 2–8 and 9–
16. They are the same as for track 1. For more information,
please see "Track 01 (Track Number):," above.
▼2–1(2): Menu Command
• 0: Memory Status ☞p.191
• 1: Exclusive Solo ☞p.73
• 2: Rename Song ☞p.191
• 3: Delete Song ☞p.191
• 4: Copy From Song ☞p.191
• 5: Load Template Song ☞p.191
• 6: Save Template Song (Save as User Template
Song) ☞p.192
• 7: FF/REW Speed ☞p.192
• 8: Set Location (Set Location for Locate Key) ☞p.192
• 9: GM Initialize ☞p.193
• 10: Copy From Combi (Copy from
Combination) ☞p.194
• 11: Copy from Program ☞p.195
For more information, please see "Sequencer: Menu
Command" on page 191.
[00...99]
149

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents