KORG M50-88 Parameter Manual: Combi P8: Ifx (insert Effect); Combi P8–1: Ifx; Routing1 T09–16

M50 music workstation.
Hide thumbs
   
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419

COMBI P8: IFX (Insert Effect)

You can also specify the bus routing for the program used by
each of the timbres, 1–16. For instance, you can:
• Send the output of a timbre to an insert effect
• Route a sound to an insert effect
COMBI P8–1: IFX
8–1–1: Routing1 T01–08,
8–1–2: Routing1 T09–16
8–1
–1a
8–1
–1b
8–1
–1c
8–1
–1d
Specifies the bus to which the program oscillator(s) used by
timbres 1–8 and 9–16 will be sent. You can also set the send
levels to the master effects from this page.
8–1–1(2)a: Routing Map
This shows the status of the insert effects.
This area shows the insert effect routing (Bus (IFX/Output)
Select), the name of the assigned effect, the on/off status,
chaining, and the output bus that follows the insert effect.
The type of insert effect, the on/off status, and the chain
settings can be edited in the 8–1–3: Insert FX Setup page.
8–1–1(2)b: Combination Name
8–1–1(2)c: Timbre Info
For more information, please see "2–1: EQ Trim T01–08, 2–2:
EQ Trim T09–16" on page 93.
8–1–1(2)d: Routing1
Bus (IFX/Output) Select
This specifies the output bus for the timbre's program
oscillator. This parameter can also be edited from the P8–2:
IFX Routing 2 T01–08, T09–16 page.
L/R: Output to the L/R bus.
IFX1...5: Output to the IFX1–5 buses.
Off: The timbre will not be output from the L/R bus, or
IFX1–5 buses. Choose the Off setting if you want the
program oscillator output of the timbre to be connected in
series to a master effect. Use Send1 (to MFX1) and Send2 (to
MFX2) to specify the send levels.
Tip: You can create a wide variety of routings by using each
timbre's Bus (IFX/Output) Select and the Chain to and
Chain settings (Combi 8–1–3b) that follow the insert effect.
COMBI P8: IFX (Insert Effect) 8–1–1: Routing1 T01–08, 8–1–2: Routing1 T09–16
8–1
–1
Menu
[DKit, L/R, IFX1...5, Off]
• Make detailed settings for insert effects
• Make common LFO settings for effects
For more details on the Insert Effects, please see the "Effect
Guide" on page 271.
Example: Inserting a single IFX into multiple timbre
Example: Inserting a separate IFX into each timbre, and then insert-
ing an IFX at the final stage
Example: Sharing a portion of a timbre's IFX chain with another tim-
bre
DKit: This can be selected only if the timbre's program is a
drum program (Oscillator Mode Drums).
The Bus (IFX/Output) Select, FX Control Bus, Send1, and
Send2 (Global 5–4b) settings for each key of the selected
Dkit will be used. Check this setting if you want to apply an
individual insert effect to each drum instrument.
Tip: In most preloaded drumkits, the drum instruments have
the same Bus (IFX/Output) Select settings according to their
type, as follows.
Snares → IFX1
Kicks → IFX2
Other → IFX3
If you want to edit these routings, use the DrumKit IFX
Patch menu command. For more information, please see
"DrumKit IFX Patch" on page 123.
113

Advertising

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: