Download Print this page

KORG M50-88 Parameter Manual: Velocity Zone

M50 music workstation.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419

Advertisement

Program mode
2–7: Velocity Zone
2–7a
2–7b
2–7a: OSC 1/2 Velocity Zone
You can specify the velocity zone for each of the four
multisamples of the oscillator. Here you will specify the
velocity zone for each oscillator.
These velocity zones take precedence over the velocity
settings for the individual MS1–4.
OSC1 Top
This sets the highest velocity at which the Oscillator 1 will
sound.
Note: The OSC1 Top velocity must be greater than the
OSC1 Bottom velocity.
OSC1 Bottom
This sets the lowest velocity at which the Oscillator 1 will
sound.
Entering velocity values from the keyboard
You can enter velocity values directly by playing them on
the keyboard. To do so:
1. Select OSC1 Top or OSC1 Bottom.
2. Hold down the ENTER switch.
3. While holding ENTER, play a note on the keyboard at
the desired velocity.
OSC2 Top
OSC2 Bottom
This specifies the maximum and minimum velocity values
for which oscillator 2 will sound.
See OSC1 Top and OSC1 Bottom, above.
2–7b: OSC1/2 Note-On Control
OSC1 Delay
This specifies the time from when you press a key until
oscillator 1 actually begins to sound.
This is most useful in Double Programs, for delaying one
oscillator in relation to the other.
KeyOff is a special setting. Instead of delaying the sound by
a particular amount of time, the sound will play as soon as
you release the key. You can use this to create the "click"
heard when a harpsichord note is released, for instance.
In general, when you use the KeyOff setting, it's also best to
set the oscillator's Amp EG Sustain Level to 0.
Mode
Normally, you play notes simply by pressing keys on the
keyboard. In special cases, however, you can set this
parameter so that you must first be holding down the
26
[001...127]
[001...127]
[001...127]
[001...127]
[0000ms...5000ms, KeyOff]
[Key, Key + Damper]
damper pedal, and then press a key, in order to play a note.
For instance, this can be useful when modeling the behavior
of a piano soundboard.
Key is the normal mode.
2–7
Menu
When you select Key + Damper, notes will only sound if the
damper pedal is being held down. When the damper pedal
is released, all notes will be stopped–even if they are still
being held down.
OSC2 Delay
Mode
2–7c
This specifies the time from when you press a key until
oscillator 2 actually begins to sound.
See OSC1 Delay and Mode, above.
2–7c: OSC 1/2 Velocity Zone Window
This shows the velocity zone.
This graphic reflects the OSC1 Basic and OSC2 Basic Bottom
Vel., Xfd, and Curve, and the Velocity Zone OSC1 Top,
OSC1 Bottom, OSC2 Top, and OSC2 Bottom settings.
Select
Xfade Range = 20
Curve = Linear
Bottom Velocity = 64
▼2–7: Menu Command
• 0: Write Program ☞p.73
• 1: Exclusive Solo ☞p.73
• 2: Copy Oscillator ☞p.74
• 3: Swap Oscillator ☞p.74
For more information, please see "Program: Menu
Command" on page 73.
[0000ms...5000ms, KeyOff]
[Key, Key + Damper]
84

Advertisement

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: