Download Print this page

KORG M50-88 Parameter Manual Page 94

M50 music workstation.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419

Advertisement

Combination mode
0–7c: Tone Adjust
Here, you can assign Tone Adjust parameters to the switches
and sliders in the display.
Switches 1...8
Tone Adjust switches act a little differently than switches in
the display.
When a switch is assigned to a Relative parameter, or an
Absolute parameter with more than two states:
Switch On = On Value (see below)
Switch Off = the Program's stored value
When a switch is assigned to a two-state Absolute
parameter, such as Hold, the switch status directly reflects
the parameter value:
Switch On = On
Switch Off = Off
Assign
On/Off
Value
Assign
This assigns Tone Adjust parameters to the switches in the
display. For a full list of the available choices, please see
"Common Tone Adjust Parameters" on page 8 and "Tone
Adjust Parameters" on page 9.
On Value
The parameter is set to this value when the switch is On.
When the switch is assigned to a two-state Absolute
parameter, such as Hold, this will always be the same as the
Switch Status (see below).
Switch Status
This simply shows whether the switch is On or Off.
86
[Depends on parameter]
[Off, On]
Sliders 1–8
Assign
This assigns Tone Adjust parameters to the sliders in the
display. For a full list of the available choices, please see
"Common Tone Adjust Parameters" on page 8 and "Tone
Adjust Parameters" on page 9.
Assignments are exclusive
Per-Oscillator parameters apply to OSC1 and 2 individually,
and are marked as such: OSC1 and OSC2.
Each slider can be assigned to only one parameter, and each
parameter can be assigned to only one slider.
To swap a parameter from one slider to another, you'll need
to first un-assign it from the old slider, and then assign it to
the new slider.
Value
This shows the current value of the parameter. The range of
values will vary depending on the parameter assigned to the
slider.
▼0–7: Menu Command
• 0: Write Combination ☞p.120
• 1: Exclusive Solo ☞p.73
• 2: Copy from Program ☞p.120
• 3: Copy Tone Adjust ☞p.121
• 4: Reset Tone Adjust ☞p.122
For more information, please see "Combination: Menu
Command" on page 120.

Advertisement

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: