069: Tape Echo Bpm - Korg M50-88 Parameter Manual

Effect Guide

069: Tape Echo BPM

This is a tape echo that lets you synchronize the delay time
to the tempo of the song.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
+
Saturation
Trim Pre Tone
Right
BPM
Tempo
Base Note x Times
BPM
D -mod
MIDI,
BPM (Delay) 40.00...
300.00
a
Tap1 Dmod
Off...Tempo
Src
Tap1 Delay
...
Note
b Times x1...x32
Time Over? ---, OVER!
Tap1 Dmod
...
Note
c
Times x1...x32
Tap2
d 0...100
Position [%]
e Tap3
0...100
Position [%]
Tap1 Level 0...100
Pan L, 1...99, R
f
FB Amt –100...+100
Tap2 Level 0...100
Pan L, 1...99, R
g
FB Amt –100...+100
Tap3 Level 0...100
Pan L, 1...99, R
h
FB Amt –100...+100
Feedback 0...100
Src Off...Tempo
i
Amt –100...+100
High Damp
0...100
[%]
j
Low Damp
0...100
[%]
k Saturation 0...100
Input Trim 0...100
l
Pre Tone 0...100
Wow Flutter
0.02...1.00
[Hz]
m
Wow Flutter
0...100
depth
334
(3)
(2)
(1)
Feedback Amt Level Pan
Tape
Delay
High / Low Damp
Wah Flatter Tap2/3 Position
Delay Time
MIDI syncs to the system
tempo; 40–300 sets the tempo
manually for this individual
effect p.322
Selects the modulation source
of the delay time p.334
Selects the type of notes to
specify the delay time (tap1)
p.322, p.334
Sets the number of notes to
specify the delay time (tap1)
p.322, p.334
Displays an error message
when the delay time exceeds
the upper limit p.334
Selects the note value used to
specify the delay time when the
modulation is at maximum
p.334
Specifies the number of notes
used to specify the delay time
when the modulation is at
maximum p.334
Sets the position of Tap 2
relative to the Tap 1 delay time
the depth of pitch variation
p.329
Sets the position of Tap 3
relative to the Tap 1 delay time
the depth of pitch variation
p.329
Sets the Tap1 output level
Sets the stereo image of tap1
Sets the Tap1 feedback amount
p.329
Sets the Tap2 output level
Sets the stereo image of tap2
Sets the Tap2 feedback amount
p.329
Sets the Tap3 output level
Sets the stereo image of tap3
Sets the Tap3 feedback amount
p.329
Sets the amount of feedback
for Taps 1, 2, and 3 p.329
Selects the modulation source
of feedback amount
Sets the depth by which
feedback amount will be
modulated
Sets the damping amount in
the high range
Sets the damping amount in
the low range
Sets the distortion amount
Sets the input gain
Sets the tone of the input
Sets the frequency at which
pitch variation will occur
Sets the depth of pitch
variation
Wet/Dry
n Src
Amt
a: Tap1 Dmod Src
b: Tap1 Delay Note
Wet / Dry
b: Times
c: Tap1 Dmod Note
c: Times
If Tap1 Dmod Src is Off or the selected modulation is at 0,
the delay time will be the length specified by Tap1 Delay
Note and Times.
Wet / Dry
If Tap1 Dmod Src is other than Off, the delay time will
change so that it will be as specified by Tap1 Dmod Note
and Times when the maximum modulation is reached.
b: Time Over?
You can set the delay time up to 5,400msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the
display. Set the delay time parameters so that this message
will not appear. Time Over? is only a display parameter.
Dry, 1 : 99... Sets the balance between the
99 : 1, Wet effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry