KORG M50-88 Parameter Manual: Delay T01–08, 4–6: Delay T09–16

M50 music workstation.
Hide thumbs
   
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419
Bottom Slope
Specifies the number of velocity steps over which the
original volume will be reached, starting from the Bottom
Velocity.
0: The volume will be at the original value from the bottom
velocity.
120: The volume will decrease as the velocity approaches the
bottom velocity.
Bottom Velocity
Specifies the minimum velocity value that will sound each
timbre.
How volume will change according to keyboard location
Volume
Bottom Slope
Bottom Velocity
Top Velocity and Bottom Velocity settings can also be input
by holding down the ENTER switch and playing a note on
the keyboard.
Timbre 02...08, 09...16 (Timbre Number):
These are the velocity zone settings for timbres 2–8 and 9–
16. They are the same as for timbre 1. For more information,
please see "Timbre 01 (Timbre Number):," above.
▼4–3(4): Menu Command
• 0: Write Combination ☞p.120
• 1: Exclusive Solo ☞p.73
• 2: Copy from Program ☞p.120
For more information, please see "Combination: Menu
Command" on page 120.
[000...120]
[001...127]
Velocity
Top Slope
Top Velocity
COMBI P4: Zone/Delay 4–5: Delay T01–08, 4–6: Delay T09–16
4–5: Delay T01–08,
4–6: Delay T09–16
4–5a
4–5b
4–5c
This specifies the time (delay) from when the timbres 1–8
and 9–16 receive a note-on until the sound begins.
4–5(6)a: Combination Name, Tempo
4–5(6)b: Timbre Info
For more information, please see "2–1: EQ Trim T01–08, 2–2:
EQ Trim T09–16" on page 93.
4–5(6)c: Delay
Timbre 01 (Timbre Number):
Delay Time [ms]
Specifies the time (delay time) from note-on until the timbre
begins to produce sound, in units of ms (1/1000th of a
second). This setting is available if MIDI/Tempo Sync. is set
to Off.
KeyOff: The note will begin sounding at note-off. In this
case, the sound will not die away if the sustain level of the
program's amp EG is other than 0. This setting is used when
creating harpsichord sounds.
Normally you will set this to 0000.
MIDI/Tempo Sync.
The time (delay time) from note-on until the timbre
produces sound will be specified in note length units
relative to the (Tempo).
On (checked): Specify the delay time in terms of a Base
Note and Times relative to the Tempo. For example if Base
Note = , Times = 01, and Tempo = 60 BPM, the delay time
will be equivalent to 1000 ms.
Off (unchecked): The delay time will be set by the Delay
Time setting.
Base Note
Times
It specifies the time (delay time) from note-on until the
timbre begins to produce sound, in terms of a note value
relative to the
(Tempo) (Combi 0–1(2)a).
Use Base Note to specify the desired note value, and use
Times to extend that note value by the specified multiple.
For example if you set Base Note to a quarter note ( ) and
Times to 02, that timbre will sound with a delay of a half
note ( ). Even if you change (Tempo) (Combi 0–1(2)a), the
delay time will always be a half note ( ). If you use these
parameters to specify a delay of a half note ( ). In this case,
a Tempo of 60.00 BPM will produce a 2000 ms delay, and a
Tempo of 120.00 BPM will produce a 1000 ms delay.
[0000...5000ms, KeyOff]
[Off, On]
[ ,
, ,
, ,
, ,
, , ]
[01...32]
4–5
Menu
101

Advertising

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: