Korg M50-88 Parameter Manual page 193

M50 series music workstation
Table of Contents

Advertisement

The Master Track setting is ignored. The last-selected
Track 01–16 will be used.
Keyboard & Assigned Graphics
This shows the selected key, and the keys to which a pattern
has been assigned by the RPPR function. See diagram below.
Non-assignable keys
Assigned keys
Selected key
Key range
C4
10–3b: RPPR Setup
KEY (Key Select)
Specifies the key to which you want to assign an RPPR
pattern.
The following parameters will apply to the key that you
select here.
This can also be selected by holding down the ENTER
switch and playing a note on the keyboard.
Assign
On (checked): When you play the key specified by KEY, the
pattern selected in Pattern will be triggered.
Off (unchecked): That key will sound the currently selected
track at the corresponding pitch, just as in normal Sequencer
mode.
Mode
Specifies the way in which the pattern assigned to the
specified KEY will be played.
Once: When you press the key, the complete pattern will
play once to the end and then stop.
Manual: The pattern will continue repeating as long as you
continue holding the key, and will stop as soon as you
release the key.
Endless: The pattern will continue repeating even after you
release the key. To stop the pattern playback, press any note
below C2, or press the same key once again.
Key-on
Key-off
START
STOP
Once
START
STOP
Manual
START
Endless
Shift
Adjusts the playback pitch of the pattern for the specified
KEY in semitone steps over a range of ±1 octave.
With a setting of 0, the pattern will be played at its original
pitch.
Sync
Specifies the way in which the pattern playback will be
synchronized when you press the specified KEY.
Off: The pattern will begin playing at the moment you press
the note.
Beat: The pattern will synchronize to the beat of the other
patterns that are already in play. This setting is suitable
when you wish to play phrase patterns in unison.
Not assigned keys
Key range
[C#2...C8]
[Off, On]
[Once, Manual, Endless]
Same key, or C2
Key-on
STOP
[–12...+12]
[Off, Beat, Measure, SEQ]
SEQ P10: Pattern/RPPR 10–3: RPPR Setup
Measure: The pattern will synchronize to the measures of
the pattern that was started by the first key. This setting is
suitable for rhythm, bass or drum patterns.
SEQ: The pattern will synchronize to the measures of the
sequencer song.
Sync settings
Key 1 on
Key 2 on
Song
Patterns 1 and 2 are set to
Mode=Manual, and have
identical Sync settings
Sync: Off
Pattern 1
Pattern 2
Sync: Beat
Pattern 1
Pattern 2
Sync: Measure
Pattern 1
Pattern 2
Sync: SEQ
Pattern 1
Pattern 2
• When Beat or Measure are selected, pattern playback
will begin when you press the first key. The second and
subsequent patterns that are triggered from the
keyboard will synchronize to the pattern that was
started by the first key; with a setting of Beat they will
synchronize in steps of a beat, and with a setting of
Measure they will synchronize in steps of a measure.
• When SEQ is selected, the pattern will play back in
synchronization with the measures of the sequencer
song. The pattern will synchronize with the currently-
playing song, so you must start the song before you play
notes on the keyboard.
• Beat, Measure, and SEQ will cause the pattern to start
immediately if you play the key within a thirty-second
note of the timing of the respective beat or measure, but
if you play the key later than this, the start of the pattern
will be delayed by a beat.
• Set this to SEQ if you want pattern playback by RPPR to
be synchronized to the currently-running arpeggiator.
Note: If you want the arpeggiator performance to
synchronize to the currently-running RPPR playback, turn
Off the arpeggiator's Key Sync. The arpeggiator will
synchronize to the beat based on the RPPR playback timing.
Note: If you want the drum track pattern performance to
synchronize to the currently-running RPPR playback, turn
On the drum track function's Sync (in each mode, the Drum
Track page Trigger). The drum track will be triggered at
intervals of one measure at the RPPR playback timing.
Stopping RPPR pattern playback
You can stop all currently-running RPPR pattern playback
by pressing C2 or any lower key.
Pattern playback will stop immediately for keys whose Sync
parameter is set to Off, but pattern playback for other keys
will stop at the beginning of the beat or measure. You can
immediately stop pattern playback for keys whose Sync is
On by pressing C2 or a lower key twice in rapid succession.
Key 1 off
185

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents