5-2: Osc1 Lfo2; 5-5: Osc2 Lfo1; 5-6: Osc2 Lfo2 - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

Program mode
Int Mod AMS (Intensity Mod AMS)
This selects a secondary AMS source to scale the intensity of
AMS1.
For a list of AMS sources, please see "AMS (Alternate
Modulation Source) List" on page 374.
Intensity
This controls the depth and direction of the Int Mod AMS.
Even if the main AMS1 Intensity is set to 0, Int Mod AMS
can still control the final amount of AMS A over the full +/–
99 range.
For example, if AMS1 is set to the Pitch EG, and Int Mod
AMS is set to JS+Y:CC#01, positive settings mean that YS+Y
will increase the intensity of the Pitch EG modulation of
LFO Frequency.
AMS2 (Freq. AMS2)
This selects the second AMS source for the LFO1's
frequency. For a list of AMS sources, please see "AMS
(Alternate Modulation Source) List" on page 374.
Intensity
This controls the amount of modulation from AMS2 (Freq.
AMS2).
5–1c: Frequency MIDI/Tempo Sync.
MIDI/Tempo Sync.
When MIDI/Tempo Sync is On, the LFO will synchronize to
the system tempo, as set by either the Tempo knob or MIDI
Clock. The LFO speed will be controlled by the Base Note
and Times parameters, below. All settings for Frequency
and Frequency Modulation will be ignored.
When MIDI/Tempo Sync is Off, the Frequency and
Frequency Modulation settings will determine the speed of
the LFO, and the tempo settings will have no effect.
Base Note (Sync. Base Note)
This sets the basic speed of the LFO, relative to the system
tempo. The values range from a 32nd note to a whole note,
including triplets.
Times (Sync. Times)
This multiplies the length of the Base Note. For instance, if
the Base Note is set to a sixteenth note, and Times is set to
03, the LFO will cycle over a dotted eighth note.
▼5–1: Menu Command
• 0: Write Program ☞p.73
• 1: Exclusive Solo ☞p.73
• 2: Swap LFO 1&2 ☞p.75
For more information, please see "Program: Menu
Command" on page 73.
50
[List of AMS Sources]
[–99...+99]
[List of AMS Sources]
[–99...+99]
[Off, On]
[ ... ]
[01...32]
5–2: OSC1 LFO2
This is Oscillator 1's second LFO. Its parameters are exactly
the same as those for the first LFO, as described under "5–1:
OSC1 LFO1" on page 48–except that LFO1 cannot modulate
LFO2.
5–5: OSC2 LFO1
This page controls Oscillator 2's first LFO. It is available only
when the Oscillator Mode is set to Double; if not, the page
will be grayed out.
The parameters are identical to those for Oscillator 1, as
described under "5–1: OSC1 LFO1" on page 48.
5–6: OSC2 LFO2
This page controls Oscillator 2's second LFO. It is available
only when the Oscillator Mode is set to Double; if not, the
page will be grayed out.
Its parameters are exactly the same as those for the first LFO,
as described under "5–1: OSC1 LFO1" on page 48–except
that LFO1 cannot modulate LFO2.

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents