Korg M50-88 Parameter Manual page 202

Sequencer mode
Copy From Combi (Copy from
Combination)
This command copies the parameters of the specified
combination to the setting data of the currently selected
song.
Note: Only the timbres used by the combination will be
copied. Timbres in the combination whose Status is Off will
not be copied. If any timbres are set to Mute, the
corresponding tracks of the song will be set to a Status of
Off.
1. In Combination, select the copy source destination.
2. Use the IFXs, MFXs and TFX check boxes to specify
whether you want the effect settings of the combina-
tion to be copied as well.
IFXs: All insert effect settings of the copy-source
combination (the contents of the Insert FX Setup page and
the IFX1–5 effect parameters) will be copied.
MFXs: All master effect settings of the copy-source
combination will be copied.
TFX: All total effect settings of the copy-source combination
will be copied.
3. Specify the desired Auto adjust Arp setting for Multi
REC setting.
You have the option of checking the Auto adjust Arp setting
for Multi REC. As necessary, this function will adjust the
MIDI channel etc. of any tracks that need to be changed,
and/or add new tracks, in order to ensure that when you
perform multi-recording with the arpeggiator on, the same
sound will be reproduced during recording as during
playback.
Note: This function makes adjustments depending on the
ARP ON/OFF state of the combination. When you copy a
combination that was written with the arpeggiator turned
off, it is assumed that you will leave the arpeggiator off in
the song. If you want to use the arpeggiator in the song, you
should write the combination with the arpeggiator turned
on, and then copy it to the song.
If this is checked, the MIDI channels etc. of the tracks will be
corrected. Multi REC (Seq 0–1–8b) and PLAY/MUTE/REC
(Seq 0–1–1(2)a) will also be set automatically.
In addition, Recording Setup, Overwrite (Seq 0–1–8b) will
be selected. (Note that the automatically-set Multi REC and
PLAY/MUTE/REC will be reset when you re-select the
song.)
Note: For details on the data that will be adjusted, see below.
The content described here will be corrected automatically.
Depending on the settings of the combination, it may be
necessary to make additional changes to the track settings in
addition to the settings here.
194
If the recorded performance is not reproduced
correctly during playback
If you use the menu command Copy From Combi to copy
the settings of a combination, and then perform multi-track
recording with the arpeggiator turned on, there may be
cases in which the performance during recording is not
reproduced correctly during playback.
Multiple tracks that are set to the same MIDI channel are
combined into a single stream of performance data during
recording. If there is a track with the same MIDI channel as
the track being played by the arpeggiator, the data played
by the arpeggiator will be combined with the performance
data that was played manually, and all of this data will be
sounded by each track of the same channel (if Status is INT).
In such cases, you can solve the problem by creating a track
that will drive the arpeggiator on a different MIDI Channel.
If the recorded performance is not reproduced by the
playback, check the following conditions.
These settings can be executed automatically if you check
Auto adjust Arp setting for Multi REC in the menu
command Copy From Combi. Normally, you will check this
to execute the settings. In this case, these adjustments will
not be necessary, but you can verify here that the automatic
adjustments have been made.
• SEQ P7: ARP/DT– ARP Setup T01–08 page
Arpeggiator Run A, B, and Arpeggiator Assign settings
• SEQ P3: Track Param– MIDI Ch T01–08 page
MIDI Channel settings
If Arpeggiator Run A and B are checked, and the
arpeggiator is assigned to a track, make sure that MIDI
Channel (Global P1: MIDI) is set to other than 01.
Make sure that the global MIDI channel (Global P1: MIDI,
MIDI Channel) is set to 01.
Arpeggiator Run MIDI Channel
01 only
If either "A" or "B" are
checked
01 02, 01 03, etc.
01 only
If both "A" and "B" are 01 02, 01 03, etc.
checked
01 02 03, etc.
*a If the "MIDI Channel" of multiple tracks operated by the
arpeggiator is set only to 01, refer to the lines for "01
only." If the "MIDI Channel" settings are 01 and one
other channel, such as 01 and 02, then refer to the lines
for "01 02, etc." If the "MIDI Channel" settings are 01 and
multiple other MIDI channels, such as 01 and 02 and 03,
then refer to the line for "01 02 03, etc."
*a
Correction
Correction required
No correction required
Correction required
Correction required for
only one
No correction required/
*b
Correction required