1-2: Midi Routing - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

1–2: MIDI Routing
1–2a
1–2b
Here, you can make MIDI Routing and MIDI Filter settings
for the entire M50.
Note: To transmit MIDI exclusive dump data, you'll use the
menu commands of the P1: MIDI page.
1–2a: MIDI Routing
Chord Trigger SW MIDI Out
[Chord Trigger SW CC/Note, Chord Notes]
This setting specifies the MIDI messages that are output
when you press a chord trigger switch.
Chord Trigger SW CC/Note: When you press a switch, the
MIDI note number or MIDI control change message
specified by the chord trigger switches SW1–SW4 (Global 2–
2c) setting will be transmitted.
If the setting is off, no MIDI message will be transmitted.
Chord Notes: When you press a switch, the (up to eight)
MIDI note-on/off messages (and velocities) specified by the
chord trigger switches SW1–SW4 (Global 1–4b) setting of
each program, combination, or song will be transmitted. If
all notes are turned off, no MIDI messages will be
transmitted.
ARP Controllers MIDI Out
[Control Change, SysEx-Param Change]
This specifies the MIDI messages that will be transmitted
when you operate the ARP ON/OFF switch or when you
operate knobs 1–4 with control surface ARP selected.
Control Change: Operating the ARP ON/OFF switch or
knobs 1–4 will transmit the MIDI control change messages
that are assigned in Global P2–2: Controllers "SW – ARP
ON/OFF" and "KNOB1 – ARP GATE" – "KNOB4 – ARP
OCTAVE."
SysEx-Param Change: Operating the ARP ON/OFF switch
or knobs 1–4 will transmit MIDI System Exclusive
parameter change messages for the parameters (arpeggiator
on/off, Gate, Velocity, Length, Octave) assigned to the
switch and knobs.
1–2b: MIDI Filter
Enable Program Change
1–2
On (checked): Program changes will be transmitted and
Menu
received.
In Program mode (P0: Play), the program will be switched
when a program change message is received on the global
MIDI channel specified by MIDI Channel (Global 1–1a).
When you switch programs, a program change message will
be transmitted on the global MIDI channel.
In Combination mode (P0: Play), the combination will be
switched when a program change message is received on
the global MIDI channel. However, it is possible to set the
Enable Combination Change parameter so that the
combination is not switched. When a program change is
received on the channel specified for each timbre by MIDI
Channel (Combi 3–1(2)c), the program of that timbre will be
switched. However, the program changes for each timbre
will be affected by the setting of the Enable Program
Change parameter (Combi 5–1–1(2)c).
When you switch combinations, a program change message
will be transmitted on the global MIDI channel, and also
transmitted simultaneously on the channel of timbres whose
Status (Combi 3–1(2)c) is set to EXT or EX2.
In Sequencer mode, incoming program change messages on
a channel that corresponds to a track whose Status (Seq 3–
1(2)c) is set to INT or BTH will switch programs on that
track.
When you select a song or play back sequencer data,
program changes will be transmitted on the channels of
tracks whose Status is set to BTH, EXT, or EX2.
Off (unchecked): Program changes will not be transmitted
or received.
Bank Change
On (checked): The Bank Select control change message will
be transmitted together with program change messages.
This is valid when Enable Program Change is checked.
Off (unchecked): Bank Select messages will not be
transmitted or received.
When recording on the internal sequencer, bank select
messages will be recorded regardless of this setting.
However for playback, this setting will apply.
Combination Change
On (checked): When in Combi P0: Play, an incoming
program change message on the global MIDI channel set by
MIDI Channel (Global 1–1a) will switch combinations.
This is valid when Enable Program Change is checked.
An incoming program change on a channel other than the
global MIDI channel will switch the program of any timbre
that matches that MIDI channel.
Off (unchecked): An incoming program change message on
the global MIDI channel will switch the program of any
timbre whose MIDI Channel (Combi 3–1(2)c) matches the
global MIDI channel. The combination will not be switched.
The program changes for each timbre will be affected by the
setting of the Enable Program Change parameter (Combi 5–
1–1(2)c).
Global P1: MIDI 1–2: MIDI Routing
[Off, On]
[Off, On]
[Off, On]
223

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents