028: St. Biphase Mod; (Stereo Biphase Modulation) - Korg M50-88 Parameter Manual

M50 series music workstation
Table of Contents

Advertisement

Effect Guide
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
j
Src
Off...Tempo
Amt
–100...+100
g: High/Low Split Point
This parameter sets the frequency that splits the high and
low range. Only the high range will be sent to the chorus
block.
h: Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.

028: St. Biphase Mod.

(Stereo Biphase Modulation)

This stereo chorus effect adds two different LFOs together.
You can set the Frequency and Depth parameters for each
LFO individually. Depending on the setting of these LFOs,
very complex waveforms will create an analog-type,
unstable modulated sound.
Stereo In - Stereo Out
Left
Right
LFO1: Tri / Sine
LFO2: Tri / Sine
LFO1
Triangle,
Waveform
Sine
Triangle,
LFO2
a
Sine
0 deg,
Phase Sw
180 deg
LFO1
Frequency
0.02...30.00
[Hz]
b
Src
Off...Tempo
–30.00...
LFO1 Amt
+30.00
LFO2
Frequency
0.02...30.00
[Hz]
c
–30.00...
Amt
+30.00
Individual,
LFO1 Type
Common1,
Common2
d
CmnLFO
–180...+180
Offset [deg]
Individual,
LFO2 Type
Common1,
Common2
e
CmnLFO
–180...+180
Offset [deg]
Depth1
0...100
f
Src
Off...Tempo
Amt
–100...+100
Depth2
0...100
g
Amt
–100...+100
308
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry
Chorus/Flanger
High Damp
Feedback
High Damp
Chorus/Flanger
180 [degree]
Selects LFO1 waveform
Selects LFO2 waveform
Switches the LFO phase
difference between left and
right
Sets the LFO1 speed
Selects the modulation source
of LFO1&2 speed
Sets the modulation amount of
LFO1 speed
Sets the LFO2 speed
Sets the modulation amount of
LFO2 speed
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2
p.297
Sets the phase offset when
LFO1 Type = Common 1 or
Common 2
p.297
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2
p.297
Sets the phase offset when
LFO2 Type = Common 1 or
Common 2
p.297
Sets the depth of LFO1
modulation
Selects the modulation source
of LFO1&2 modulation depth
Sets the modulation amount of
LFO1 modulation depth
Sets the depth of LFO2
modulation
Sets the modulation amount of
LFO2 modulation depth
L Pre Delay
[msec]
h
R Pre Delay
[msec]
Feedback
i
High Damp
[%]
Wet/Dry
j
Src
Amt
LFO1
LFO2
Wet / Dry
Wet / Dry
Sets the delay time for the left
0.0...50.0
channel
Sets the delay time for the right
0.0...50.0
channel
Sets the feedback amount
–100...+100
Sets the damping amount in
0...100
the high range
–Wet...
Sets the balance between the
–1 : 99, Dry,
effect and the dry input
1 : 99...Wet
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
Bi-Phase Modulation LFO
Depth1
+
Depth2
p.307
p.307
p.308
p.299

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents