Dell PowerConnect B-RX Configuration Manual page 982

29
Displaying IPv4 IS-IS information
Displaying summary information
To display summary information for all the LSPs in the BigIron RX's LSP databases, enter the
following command at any level of the CLI.
BigIron RX)# show isis database
IS-IS Level-1 Link State Database
LSPID
RX-1.00-00
RX-1.01-00
RX-1.02-00
RX.00-00*
IS-IS Level-2 Link State Database
LSPID
RX-1.00-00
RX-1.01-00
RX-1.02-00
RX.00-00*
0000.0100.0003.00-00
0000.0100.0003.00-01
The command in this example shows information for the LSPS in the BigIron RX's Level-1 and
Level-2 LSP databases. Notice that the display groups the Level-1 and Level-2 LSPs separately.
Syntax: show isis database [<lsp-id> | detail | l1 | l2 | level1 | level2]
The <lsp-id> parameter displays summary information about a particular LSP. Specify an LSPID for
which you want to display information in HHHH.HHHH.HHHH.HH-HH format, for example,
3333.3333.3333.00-00. You can also enter name.HH-HH, for example, RX.00-00.
The detail parameter displays detailed information about the LSPs. Refer to
information"
The l1 and level1 parameters display the Level-1 LSPs only. You can use either parameter.
The l2 and level2 parameters display the Level-2 LSPs only. You can use either parameter.
The show isis database summary display shows the following information.
TABLE 135
This field...
LSPID
LSP Seq Num
LSP Checksum
LSP Holdtime
ATT
910
LSP Seq Num
0x0000000c
0x00000004
0x00000001
0x0000000b
LSP Seq Num
0x0000000d
0x00000004
0x00000001
0x0000000b
0x0000001f
0x0000001d
on page 911.
IS-IS summary LSP database information
Displays...
The LSP ID, which consists of the source ID (6 bytes), the pseudonode (1
byte), and LSPID (1 byte).
NOTE: If the address has an asterisk ( * ) at the end, this indicates that
The sequence number of the LSP.
The checksum calculated by the device that sent the LSP and used by
the BigIron RX to verify that the LSP was not corrupted during
transmission over the network.
The maximum number of seconds during which the LSP will remain
valid.
NOTE: The IS that originates the LSP sets the timer for the LSP. As a
A 4-bit value extracted from bits 4 – 7 in the Attach field of the LSP.
LSP Checksum LSP Holdtime
0xd048 963
0x09b0 957
0xc57b 961
0x23fb 1030
LSP Checksum LSP Holdtime
0x7d97 964
0x09b0 958
0x200f 962
0x5647 1030
0x761a 932
0x9c9d 606
the LSP is locally originated.
result, LSPs do not all have the same amount of time remaining
when they enter the BigIron RX's LSP database.
BigIron RX Series Configuration Guide
ATT/P/OL
1/0/0
0/0/0
0/0/0
1/0/0
ATT/P/OL
1/0/0
0/0/0
0/0/0
1/0/0
0/0/0
0/0/0
"Displaying detailed
53-1001810-01