Moving Switch Sanfran.blda.t5 Down Into An Existing Peer Group - Cisco Catalyst 8540 MSR Configuration Manual

Adding a New Lowest Level of PNNI Hierarchy

Moving Switch SanFran.BldA.T5 Down into an Existing Peer Group

After you move the first ATM switch router down to form a new peer group, you can move the remaining
ATM switch routers down into the peer group one by one. You should move the ATM switch routers
down in an order that keeps the peer group contiguous.
The following example shows how to move switch SanFran.BldA.T5 down into a peer group at level 72:
SanFran.BldA.T5# configure terminal
Enter configuration commands, one per line.
SanFran.BldA.T5(config)# atm router pnni
SanFran.BldA.T5(config-atm-router)# node 1 disable
SanFran.BldA.T5(config-pnni-node)# node 1 level 72 enable
SanFran.BldA.T5(config-pnni-node)# end
SanFran.BldA.T5#
When you move an ATM switch router down into an existing peer group, the ability to establish new
Note
connections across that ATM switch router is lost temporarily (up to several seconds).
To verify the configuration, use the show atm pnni local-node and show atm pnni hierarchy
commands. For examples of these commands, see
Switches T3 and T4, page
You can configure one or more of the ATM switch routers that have been moved down into the peer group
as a backup PGL. The following example shows how to configure SanFran.BldA.T5 as a backup PGL
for the peer group SanFran (see
SanFran.BldA.T5# configure terminal
Enter configuration commands, one per line.
SanFran.BldA.T5(config)# atm router pnni
SanFran.BldA.T5(config-atm-router)# node 2 level 56
SanFran.BldA.T5(config-pnni-node)# name SanFran
SanFran.BldA.T5(config-pnni-node)# no auto-summary
SanFran.BldA.T5(config-pnni-node)# exit
SanFran.BldA.T5(config-atm-router)# node 1
SanFran.BldA.T5(config-pnni-node)# election leadership-priority 10
SanFran.BldA.T5(config-pnni-node)# parent 2
SanFran.BldA.T5(config-pnni-node)# end
SanFran.BldA.T5#
SanFran.BldA.T5# show atm pnni local-node
PNNI node 1 is enabled and running
Node name: SanFran.BldA.T5
System address
Node ID
Peer group ID
Level 72, Priority 10 10, No. of interfaces 2, No. of neighbors 1
Parent Node Index: 2
<information deleted>
PNNI node 2 is enabled and not running
Node name: SanFran
System address
Node ID
Peer group ID
Level 56, Priority 0 0, No. of interfaces 0, No. of neighbors 0
Parent Node Index: NONE
<information deleted>
ATM Switch Router Software Configuration Guide
A-12
A-4.
Figure A-4):
47.009144556677223310111244.00603E7B2401.01
72:160:47.009144556677223310111244.00603E7B2401.00
72:47.0091.4455.6677.2233.0000.0000
47.009144556677223310111244.00603E7B2401.02
56:72:47.009144556677223300000000.00603E7B2401.00
56:47.0091.4455.6677.0000.0000.0000
End with CNTL/Z.
Configuring Second Level of PNNI Hierarchy on
End with CNTL/Z.
Appendix
OL-7396-01