Cisco Catalyst 8540 MSR Configuration Manual page 662

Configuring Frame Relay to ATM Virtual Connections
Frame Relay to Frame Relay Interworking Soft PVC Configuration Example
This section provides an example of a Frame Relay to Frame Relay network interworking soft PVC
configured between Switch A and Switch B, as shown in
interface 0/1/0:5 on Switch A.
Use the show vc interface serial command to determine that data-link connection identifier (DLCI) 43
Step 1
is available on serial interface 0/1/0:5 on Switch A:
Switch-A# show vc interface serial 0/1/0:5
Interface
Serial0/1/0:5
Serial0/1/0:5
Serial0/1/0:5
Serial0/1/0:5
Step 2 The destination (passive) side is a Frame Relay serial interface 0/0/1:9 on Switch B.
Step 3 The ATM address for the destination serial interface 0/0/1:9 on Switch B is
47.0091.8100.0000.00e0.1e79.8803.4000.0c81.8010.00.
Switch-B# show atm addresses
Switch Address(es):
47.00918100000000E01E798803.00E01E808601.00 active
Soft VC Address(es) :
47.0091.8100.0000.00e0.1e79.8803.4000.0c80.0000.00 ATM1/0/0
47.0091.8100.0000.00e0.1e79.8803.4000.0c80.0010.00 ATM1/0/1
47.0091.8100.0000.00e0.1e79.8803.4000.0c80.0020.00 ATM1/0/2
47.0091.8100.0000.00e0.1e79.8803.4000.0c80.0030.00 ATM1/0/3
<information deleted>
Soft VC Address(es) for Frame Relay Interfaces :
47.0091.8100.0000.00e0.1e79.8803.4000.0c81.8010.00 Serial0/0/1:9
47.0091.8100.0000.00e0.1e79.8803.4000.0c81.8020.00 Serial0/0/1:10
ILMI Switch Prefix(es):
47.0091.8100.0000.00e0.1e79.8803
<information deleted>
DLCI 255 is available on serial interface 0/0/1:9 Switch B.
Step 4
Switch-B# show vc interface serial 0/0/1:9
Interface Conn-Id Type X-Interface X-Conn-Id Encap Status
Serial0/0/1:9 44 SoftVC Serial3/0/0:3 54 SoftVC UP
Serial0/0/1:9 45 SoftVC Serial3/0/0:2 55 SoftVC UP
Serial0/0/1:9 76 SoftVC ATM0/1/3 0/45 SVC UP
Serial0/0/1:9 86 SoftVC ATM1/1/0 0/100 SoftVC UP
Configure the network interworking soft PVC from Switch A beginning in global configuration mode.
Step 5
Switch-A(config)# interface serial 0/1/0:5
Switch-A(config-if)# frame-relay soft-vc 43 dest-address
47.0091.8100.0000.00e0.1e79.8803.4000.0c81.8010.00 dlci 255
Note
ATM Switch Router Software Configuration Guide
20-34
Conn-Id Type
54 SoftVC
55 SoftVC
56 SoftVC
66 SoftVC
If the soft PVC originates and terminates on a Frame Relay interface, the default interworking
type is network interworking. You do not need to specify the interworking type explicitly.
Chapter 20 Configuring Frame Relay to ATM Interworking Port Adapter Interfaces
Figure
X-Interface X-Conn-Id
Serial3/0/0:3 54
Serial3/0/0:2 55
ATM0/1/3 0/45
ATM1/1/0 0/100
20-7. The source (active) side is serial
Encap Status
SoftVC UP
SoftVC UP
SVC UP
SoftVC UP
OL-7396-01