Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
rights
rights reserved.
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
CONNECTION
CONNECTION
A5 DI7 (XA1 A/5)
A5 DI7 (XA1 A/5)
(lift cutoff option S7)
(lift cutoff option S7)
A6 DI9 (XA1 A/6)
A6 DI9 (XA1 A/6)
(side guard out S13 & S17)
(side guard out S13 & S17)
A7 DI11 (XA1 A/7)
A7 DI11 (XA1 A/7)
(brake release S3)
(brake release S3)
A10 GND (XA1 A/10)
A10 GND (XA1 A/10)
(brake release/lift cutoff option)
(brake release/lift cutoff option)
A11 DI6 (XA1 A/11)
A11 DI6 (XA1 A/11)
(lower switch S5)
(lower switch S5)
A12 DI8 (XA1 A/12)
A12 DI8 (XA1 A/12)
(economy mode S1)
(economy mode S1)
A13 DI10 (XA1 A/13)
A13 DI10 (XA1 A/13)
(driver present / platform down S11)
(driver present / platform down S11)
A14 DI12 (XA1 A/14)
A14 DI12 (XA1 A/14)
(battery lock sensor option S14)
(battery lock sensor option S14)
8.2.3.2 CNB
8.2.3.2
CNB external
external connector
CONNECTION
CONNECTION
B1 PEB (XA1 B/1)
B1 PEB (XA1 B/1)
(magnetic brake Y31)
(magnetic brake Y31)
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
Input of the switch DI7. The
Input of the switch DI7. The input is activated when
it is connected to +Batt. The default function is the
it is connected to +Batt. The default function is the
controller LIFT enable input.
controller LIFT enable input.
Input of the switch DI9. The input is activated when
Input of the switch DI9. The
the external switch is opened. The
the external switch is opened. The default function is
the controller PUMP CUTBACK input. When the
the controller PUMP CUTBACK input. When the
switch is opened, the pump speed is reduced.
switch is opened, the pump speed is reduced.
Input of the switch DI11. The input is activated when
Input of the switch DI11. The
the external switch is opened to ground. The default
the external switch is opened to ground. The default
function is the controller CUTBACK1 input. When
function is the controller CUTBACK1 input. When
the switch is opened, the truck speed is
the switch is opened, the truck speed is reduced. In
the sense coil version, this input is connected to the
the sense coil version, this input is
AC motor sense
AC motor sense coil.
This is the ground of the logic board.
This is the ground of the logic board.
Input of the switch DI6. The input is activated when
Input of the switch DI6. The
it is connected to +Batt. The default function is the
it is connected to +Batt. The default function is the
controller LOWER enable input.
controller LOWER enable input.
Input of the switch DI8. The
Input of the switch DI8. The input is activated when
it is connected to +Batt. The default function is the
it is connected to +Batt. The default function is the
controller 1ST input: the pump motor turns at the
controller 1ST input: the pump motor turns
defined speed.
defined speed.
Input of the switch DI10. The input is activated when
Input of the switch DI10. The
it is connected to +Batt. The default function is the
it is connected to +Batt. The default function is the
controller 2ND input: the pump motor turns at
controller 2ND input: the pump motor turns at the
defined speed.
defined speed.
Input of the switch DI12. The input is activated when
Input of the switch DI12. The
the external switch is opened to ground. The default
the external switch is opened to ground. The default
function is the controller CUTBACK1 input. When
function is the controller CUTBACK1 input. When
the switch is opened, the truck speed is
the switch is opened, the truck speed is reduced. In
the sense coil version, this input is
the sense coil version, this input is connected to the
AC motor sense coil.
AC motor sense
connector
DESCRIPTION
DESCRIPTION
This pin outputs the positive supply (equal to +Batt)
This pin outputs the positive supply (equal
of the electro-mechanical brake coil. Depending on
of the electro-mechanical brake coil. Depending on
the hardware configuration, this pin can be
the hardware configuration, this pin can be
controlled by the microcontroller or tied to the B2
controlled by the microcontroller or tied to the
input or to the C6 input. See the connection drawing
input or to the C6 input. See the connection drawing
for more details.
for more details.
97 (244)
97 (244)
Service Manual
Service
Manual
input is activated when
input is activated when
default function is
input is activated when
reduced. In
connected to the
coil.
input is activated when
input is activated when
at the
input is activated when
input is activated when
reduced. In
connected to the
coil.
to +Batt)
the
B2
Advertisement
Table of Contents
