Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
rights
rights reserved.
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
CONNECTION
CONNECTION
C6 DI0 (XA1 C/6)
C6 DI0 (XA1 C/6)
(tiller switch S12)
(tiller switch S12)
C7 DI2 (XA1 C/7)
C7 DI2 (XA1 C/7)
(side guard in S15 and S16)
(side guard in S15 and S16)
C8 PPOT
C8 PPOT
(pressure sensor supply B42)
(pressure sensor supply B42)
C9 CPOTL
C9 CPOTL
(pressure sensor output B42)
(pressure sensor output B42)
C10 CANL (XA1 C/10)
C10 CANL (XA1 C/10)
(CAB bus green)
(CAB bus green)
8.2.3.4 CND
8.2.3.4
CND external
external connector
CONNECTION
CONNECTION
D1 ENC A (XA1 D/1)
D1 ENC A (XA1 D/1)
(traction motor encoder phase A M1)
(traction motor encoder phase A M1)
D2 PENC (XA1 D/2)
D2 PENC (XA1 D/2)
(traction motor encoder supply M1)
(traction motor encoder supply M1)
D3 PTHERM (XA1 D/3)
D3 PTHERM (XA1 D/3)
(temperature sensor R31)
(temperature sensor R31)
D4 ENC B (XA1 D/4)
D4 ENC B (XA1 D/4)
(traction motor encoder phase B M1)
(traction motor encoder phase B M1)
D5 NENC XA1 D/4)
D5 NENC XA1 D/4)
(traction motor encoder gnd M1)
(traction motor encoder gnd M1)
D6 NTHERM (XA1 D/6)
D6 NTHERM (XA1 D/6)
(temperature sensor R31)
(temperature sensor R31)
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
Input of the switch DI0. The input is activated when
Input of the switch DI0. The
it is connected to +Batt. With the logic hardware
it is connected to +Batt.
properly configured, it can be used to supply the EB
properly configured, it can be used to
and MC positive voltage. The default function is the
and MC positive voltage. The default function
controller TILLER input.
controller TILLER input.
Input of the switch DI7. The
Input of the switch DI7. The input is activated when
it is connected to +Batt. The default function is the
it is connected to +Batt. The default function is the
controller H&S (Hard & Soft) request input. When
controller H&S (Hard & Soft) request input. When
this input is closed, the truck performances are
this input is closed, the truck performances are
modified.
modified.
Potentiometer's positive supply. The hardware has
Potentiometer's positive supply. The hardware has
to be configured to the output +12 V or +5 V.
to be configured to the output +12 V or +5 V.
Lift/lower potentiometer wiper input.
Lift/lower potentiometer wiper input.
Low level CAN bus voltage I/O.
Low level CAN bus voltage I/O.
connector
DESCRIPTION
DESCRIPTION
Traction motor encoder phase A.
Traction motor encoder phase A.
Encoder positive supply. The hardware has to be
Encoder positive supply. The hardware has to be
configured to the output +12 V or +5 V.
configured to the output +12 V or +5 V.
Traction motor's thermal sensor positive input
Traction motor's thermal sensor positive input
5VDC. The resistance of the sensor is 581 Ω at
5VDC. The resistance of the sensor is 581
20˚C.
20
˚C.
Traction motor encoder phase B.
Traction motor encoder phase B.
Negative of the encoder.
Negative of the encoder.
Negative (GND) for the motor thermal sensor.
Negative (GND) for the motor thermal sensor.
99 (244)
99 (244)
Service Manual
Service
Manual
input is activated when
With the logic hardware
supply the EB
is the
input is activated when
Ω at
Advertisement
Table of Contents
