Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
CODE
CODE
185
185
186
186
187
187
188
188
189
189
190
190
192
192
rights reserved.
rights
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
TRUCKTOOL
TRUCKTOOL
AND
AND
DISPLAY
DISPLAY
Height sensor mismatch
Height sensor mismatch
HT SENS.MISM
HT SENS.MISM
If the truck is not equipped with side stabilizers, check that the parameter INITIAL LIFT is
If the truck is not
equipped with side stabilizers, check that the parameter INITIAL LIFT is not
set to 2.
set to 2.
If the truck is equipped
If the truck is equipped with side stabilizers:
with side stabilizers:
Check the wiring of the height sensor.
Check the wiring of the height
•
•
Disconnect the height sensor and test the redundant switches. If the states are not equal,
Disconnect the height sensor and test the redundant
•
•
test if the switch works by moving a magnet in
test if the switch works by moving a magnet in front of it.
Check that the magnet counterpart (attached to the lifting
Check that the magnet counterpart (attached to the lifting carriage) is intact.
•
•
Check the wiring of the encoder card (extra I/O).
Check the wiring of the encoder card (extra
•
•
If the problem persists, replace the height
If the problem persists, replace the height sensor.
Motor temperature notification
Motor temperature notification
WARN. MOT.TEMP
WARN. MOT.TEMP
This is only a notification.
This is only a notification. To limit further heat generation,
To limit further heat generation, the parameter cutback starts when
the motor temperature reaches 120˚C. The truck can be used normally.
the motor temperature reaches 120
Controller temperature notification
Controller temperature notification
WARN. TH.PROTEC
WARN. T
H.PROTECT T
This is only a notification. To limit further heat generation,
This is only a notification.
To limit further heat generation, the parameter cutback starts when
the controller temperature reaches 75˚C. The truck can be used normally.
the controller temperature reaches 75
Load sensor value is out of range
Load sensor value is out of range
LOAD.SEN.OUT RNG
LOAD.SEN.OUT RNG
This warning indicates a pressure sensor problem. Either the pressure sensor's voltage is not
This warning indicates a pressure sensor problem. Either the pressure sensor's voltage is not
within the calibrated value range or it exceeds the calibrated values too
within the calibrated value range
Battery lock not closed
Battery lock not closed
BATTERY LOCK
BATTERY LOCK
This alarm indicates that the battery lock is not closed.
This alarm indicates that the battery lock is
In such a case, check the battery lock state
In such a case, check the battery lock state from the tester menu. If the
open while the battery is
open while the battery is mechanically locked, check the battery lock sensor operation and
mechanically locked, check the battery lock sensor operation and
wiring.
wiring.
Motor braking error
Motor braking error
BRK TIMEOUT
BRK TIMEOUT
One possible cause for this alarm is too steep braking ramp (parameter). Try to lower the
One possible cause for this alarm is too
braking ramps from the parameters. Also braking at a slope
braking ramps from the parameters. Also braking at a slope when the truck is loaded can
cause this error.
cause this error.
Waiting for EPS
Waiting for EPS
EPS RELAY OPEN
EPS RELAY OPEN
This alarm indicates that there is some problem in the steering and the
This alarm indicates that there is some problem in
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
(Alarm)
(Alarm)
sensor.
switches. If the states are not equal,
front of it.
I/O).
sensor.
(Warning)
(Warning)
the parameter cutback starts when
˚C. The truck can be used normally.
(Warning)
(Warning)
the parameter cutback starts when
˚C. The truck can be used normally.
(Warning)
(Warning)
or it exceeds the calibrated values too much.
(Alarm)
(Alarm)
not closed.
from the tester menu. If the lock is stated to be
(Alarm)
(Alarm)
steep braking ramp (parameter). Try to lower the
(Alarm)
(Alarm)
the steering and the steering has frozen.
161 (244)
161 (244)
Service Manual
Service
Manual
Stored
Stored
carriage) is intact.
Stored
Stored
much.
lock is stated to be
Stored
Stored
when the truck is loaded can
Stored
Stored
steering has frozen.
not
Advertisement
Table of Contents
