Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
rights reserved.
rights
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
PARAMETER
PARAMETER
Turtle cutback speed reduction
Turtle cutback speed reduction
TURTLE CUTBACK
TURTLE CUTBACK
Walkie mode cutback
Walkie mode cutback
WALKING CUTBACK
WALKING CUTBACK
Table 7. Submenu: adjustments
Table 7. Submenu: adjustments
PARAMETER
PARAMETER
Adjust battery voltage
Adjust battery voltage
ADJUST BATTERY
ADJUST BATTE
RY
Battery maximum value adjust
Battery maximum value adjust
BAT MAX ADJ.
BAT MAX ADJ.
Battery minimum value adjust
Battery minimum value adjust
BAT. MIN ADJ.
BAT. MIN ADJ.
BDI startup correction value
BDI startup correction value
BDI ADJ STARTUP
BDI ADJ STARTUP
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
This parameter controls the speed reduction when
This parameter controls the speed reduction when
the low speed mode is activated.
the low speed mode is activated.
Value range:
Value range:
•
•
10%: Enabled
10%: Enabled
100%: Disabled
100%: Disabled
•
•
This parameter controls the maximum speed in the
This parameter controls the maximum speed in the
pedestrian mode.
pedestrian mode.
Value range:
Value range:
10%: Slowest
10%: Slowest
•
•
100%: Fastest
100%: Fastest
•
•
DESCRIPTION
DESCRIPTION
Because the traction motor controller monitors the
Because the traction motor controller monitors the
battery discharge level, this parameter must be set
battery discharge level, this parameter must be set
to match the actual battery voltage. The difference
to match the actual battery voltage. The
between the ADJUST BATTERY VALUE parameter
between the ADJUST BATTERY VALUE parameter
value and the voltmeter reading should be
value and the voltmeter reading should be ±0.2 V.
Connect the voltmeter between –Batt and key input
Connect the voltmeter between –Batt and key input
K1/1. Use a high-quality voltmeter to check the
K1/1. Use a high-quality voltmeter to check the
battery voltage and set this parameter as close to
battery voltage and set this parameter as close to
the meter reading as possible. This measurement
the meter reading as possible. This measurement
can be carried out at any time (i.e. regardless
can be carried out at
whether the battery is full or
whether the battery is full or empty).
This parameter should be set after the
This parameter should be set after the controller has
been changed or if
been changed or if there are problems with battery
charge level monitoring.
charge level monitoring.
This parameter controls the maximum level for
This parameter controls the maximum level for
charged battery.
charged battery.
Value range:
Value range:
Level = 0: Minimum
Level = 0: Minimum
•
•
Level = 9: Maximum
Level = 9: Maximum
•
•
This parameter controls the minimum level for
This parameter controls the minimum level for
discharged battery.
discharged battery.
Value range:
Value range:
Level = 0: Minimum
Level = 0: Minimum
•
•
Level = 9: Maximum
Level = 9: Maximum
•
•
At startup, the BDI is calculated with this voltage
At startup, the BDI is c
adjust parameter.
adjust parameter.
Value range:
Value range:
Level = 0: Minimum
Level = 0: Minimum
•
•
•
•
Level = 9: Maximum
Level = 9: Maximum
149 (244)
149 (244)
Service Manual
Service
Manual
difference
±0.2 V.
any time (i.e. regardless
empty).
controller has
there are problems with battery
alculated with this voltage
Advertisement
Table of Contents
