Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
CODE
CODE
247
247
248
248
249
249
250
250
251
251
252
252
253
253
254
254
MICRO SLAVE KO
MICRO SLAVE KO
This alarm occurs if the microprocessor detects a mismatch between the commanded and
This alarm occurs if
the microprocessor detects a mismatch between the commanded and
active steering directions. In such a case, replace the steering controller.
active steering directions. In such a case, replace the
rights reserved.
rights
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
TRUCKTOOL
TRUCKTOOL
AND
AND
DISPLAY
DISPLAY
CAN-BUS communication error
CAN-BUS communication error
CAN BUS KO
CAN BUS KO
This warning occurs if the steering controller does not receive a message from the traction
This warning occurs if the steering controller does not
controller within one second. In such a
controller within one second. In such a case, check the CAN bus wiring from the COMBIACX
controller to the steering controller.
controller to the steering controller.
Steering sensor out of range
Steering sensor out of range
S.P. OUT OF RANGE
S.P. OUT OF RANGE
This alarm occurs if the command HALL sensor (or potentiometer) signal voltage is out
This alarm occurs if the command HALL sensor (or potentiometer) signal voltage is out of of
range (from 0.8 Vdc to
range (from 0.8 Vdc to 4.2 Vdc). In such a case, check that the
4.2 Vdc). In such a case, check that the connectors and cables are in
order and measure that the command sensor signal voltage is
order and measure that the command sensor signal voltage is within tolerance.
Feedback sensor out of range
Feedback sensor out of range
F.FB: OUT OF RANGE
F.FB: OUT OF RANGE
This alarm occurs if the feedback HALL sensor (or potentiometer) signal voltage is
This alarm occurs if the feedback HALL sensor (or potentiometer) signal voltage is out of range
(from 0.3 Vdc to 4.7
(from 0.3 Vdc to 4.7 Vdc). In such a case, check that the
Vdc). In such a case, check that the connectors and cables are in order
and measure that the feedback sensor signal voltage is
and measure that the feedback sensor signal voltage is within tolerance.
Internal microprocessor error
Internal microprocessor error
MICRO SLAVE
MICRO SLAVE
This alarm occurs when the internal microprocessor information does not match. In such a
This alarm occurs when the internal microprocessor information does not match. In such a
case, replace the steering controller.
case, replace the steering controller.
Internal safety contact is open
Internal safety contact is open
KM OPEN
KM OPEN
This alarm occurs when the microprocessor detects that the internal safety contact is open
This alarm occurs when the microprocessor detects that the internal safety contact is open
when it is expected to be closed. In such a case, replace the
when it is expected to
be closed. In such a case, replace the steering controller.
Internal safety contact 2 is open
Internal safety contact 2 is open
KS OPEN
KS OPEN
This alarm occurs when the microprocessor detects that the second internal safety contact is
This alarm occurs when the microprocessor detects that the second internal safety contact is
open when it is
open when it is expected to be closed. In such a
expected to be closed. In such a case, replace the steering controller.
Internal safety contact is closed
Internal safety contact is closed
KM CLOSED
KM CLOSED
This alarm occurs when the microprocessor detects that the internal safety contact is closed
This alarm occurs when the microprocessor detects that the internal safety contact is closed
when it is expected to be open. In such a case, replace the steering controller.
when it is expected to be open. In such a case, replace the steering controller.
Internal safety contact 2 is closed
Internal safety contact 2 is closed
KS CLOSED
KS CLOSED
This alarm occurs when the microprocessor detects that the second internal safety contact is
This alarm occurs when the microprocessor detects that the second internal safety contact is
https://www.forkliftpdfmanuals.com/
closed when it is expected to
closed when it is expected to be open. In such a
steering controller.
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
(Warning)
(Warning)
receive a message from the traction
case, check the CAN bus wiring from the COMBIACX
(Alarm)
(Alarm)
(Alarm)
(Alarm)
connectors and cables are in order
within tolerance.
(Alarm)
(Alarm)
(Alarm)
(Alarm)
(Alarm)
(Alarm)
case, replace the steering controller.
(Alarm)
(Alarm)
(Alarm)
(Alarm)
be open. In such a case, replace the steering controller.
case, replace the steering controller.
228 (244)
228 (244)
Service Manual
Service
Manual
Stored
Stored
connectors and cables are in
within tolerance.
Stored
Stored
out of range
Stored
Stored
Stored
Stored
steering controller.
Stored
Stored
Stored
Stored
Stored
Stored
Advertisement
Table of Contents
