Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
CODE
CODE
193
193
194
194
195
195
196
196
197
197
198
198
199
199
rights reserved.
rights
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
TRUCKTOOL
TRUCKTOOL
AND
AND
DISPLAY
DISPLAY
Sideguard inputs illegal state
Sideguard inputs illegal state
SIDEGUARD INPUTS
SIDEGUARD INPUTS
This alarm is caused by an invalid
This alarm is caused by an invalid combination of side guard inputs.
If both the side guards are in the correct position (both
If both the side
guards are in the correct position (both open or both closed), check from the
tester menu if the logic
tester menu if the logic inputs are the same. Check the correct positioning and
inputs are the same. Check the correct positioning and operation of the
side guard sensors. Also check the wiring of the sensors.
side guard sensors. Also check the wiring of the
Platform inputs illegal state
Platform inputs illegal state
PLATFORM INPUTS
PLATFORM INPUTS
This alarm is caused by an invalid
This alarm is caused by an invalid combination of operator's platform inputs.
When the operator's platform is either down with a driver standing on
When the operator's platform is either d
tester menu that the logic inputs are correct. Check the correct positioning and operation of
tester menu that the logic i
nputs are correct. Check the correct positioning and operation of the
platform sensors. Also check the sensor
platform sensors. Also check the sensor wiring.
Platform inputs inactive
Platform inputs inactive
WAITING DRIVER
WAITING DRIVER
This is a general warning indicating only that the truck is waiting for an operator.
This is a general warning indicating only that the truck is waiting for an operator.
Invalid motor resistance
Invalid motor resistance
MISMATCHED RM
MISMATCHED RM
This alarm occurs if the motor resistance is different than
This alarm occurs if the motor resistance is different than the value of the
RESIST.
RESIST.
In such a case, teach the new motor resistance value by setting the parameter MOTOR
In such a case, teach the
new motor resistance value by setting the parameter MOTOR
RESIST to 0 and saving the value while holding the tiller arm in the drive position. Restart the
RESIST to 0 and saving the value while holding the tiller arm in the drive position. Restart the
truck after the main contactor is opened. T
truck after the main contactor is opened. The new settings are active after
Motor resistance acquiring failed
Motor resistance acquiring failed
WRONG ACQ
WRONG ACQ
This warning occurs if the controller did not acquire the motor resistance value correctly.
This warning occurs if the controller did
In most cases, this alarm signals that the controller cannot inject current in the motor coils
In most cases, this alarm signals that the controller cannot
some reason. Check the motor connections. Also make sure that the main contactor is closed.
some reason. Check the motor connections. Also make sure that the main contactor is closed.
Sensorless feedback hardware error
Sensorless feedback hardware error
ERROR FEEDBACK
ERROR FEEDBACK
This alarm indicates damage to the controller's hardware which provides feedback for the
This alarm indicates damage to the controller's hardware which provides feedback for the
sensorless motor control.
sensorless motor control.
If the problem occurs permanently, replace the controller.
If the problem occurs permanently, replace the controller.
PIN teach mode
PIN teach mode
TEACHING PIN
TEACHING PIN
This warning is displayed when the PIN
This warning is displayed when the PIN code teaching procedure is active. It disappears when
the teaching is finished.
the teaching is finished.
This warning should occur only if the
This warning should occur only if the truck is equipped with a PIN
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
(Alarm)
(Alarm)
combination of side guard inputs.
open or both closed), check from the
sensors.
(Alarm)
(Alarm)
combination of operator's platform inputs.
own with a driver standing on it or up, check from the
wiring.
(Warning)
(Warning)
(Alarm)
(Alarm)
the value of the parameter MOTOR
he new settings are active after the restart.
(Alarm)
(Alarm)
not acquire the motor resistance value correctly.
inject current in the motor coils for
(Alarm)
(Alarm)
(Warning)
(Warning)
code teaching procedure is active. It disappears when
truck is equipped with a PIN code lock.
162 (244)
162 (244)
Service Manual
Service
Manual
operation of the
Stored
Stored
it or up, check from the
the
Stored
Stored
parameter MOTOR
the restart.
Stored
Stored
for
Stored
Stored
code lock.
Advertisement
Table of Contents
