Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
rights reserved.
rights
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
8.2.2
8.2.2
Zapi COMBIACX
Zapi
COMBIACX Power
The COMBIACX inverter has been developed to perform all the electric functions that
The COMBIACX inverter has been developed to perform all the electric functions that
are usually present in walkie and rider pallet trucks, stackers and low level order
are usually present in walkie and rider pallet tr
pickers.
pickers.
The controller can perform the
The controller can perform the following functions:
Controller for AC 600 W to 2 kW AC motors
Controller for AC 600 W to 2 kW
•
•
Pump controller for series wounded DC motors up to
Pump controller for series wounded DC motors up to 5 kW
•
•
Driver for the line
Driver for the line contactor coil
contactor coil
•
•
Driver for ON/OFF solenoid valves and for one proportional valve
Driver for ON/OFF solenoid valves and for one proportional valve
•
•
Low side and high side (short circuit
Low side and high side (short circuit protected) drives for electric brake coil
•
•
CAN bus interface
CAN bus interface
•
•
Interface for a CAN bus tiller
Interface for a CAN bus tiller
•
•
192 kB flash memory embedded
192 kB flash memory embedded
•
•
Software downloadable via a serial
Software downloada
ble via a serial link (internal connectors) or CAN bus (external
•
•
connector)
connector)
ESD protection on CAN bus
ESD protection on CAN bus inputs CANL and CANH
•
•
Inverter for traction AC
Inverter for traction AC asynchrono
•
•
pump motors
pump motors
Regenerative braking functions
Regenerative braking functions
•
•
8.2.3
8.2.3
Zapi COMBIACX
Zapi
COMBIACX connectors
Before any inspection or repair work, turn the
Before any inspection or repair work, turn the key switch to the OFF
disconnect the battery plug/connector, discharge all inverters and record the places of
disconnect the battery plug/connector, discharge all inverters and record the places of
the harness connections before disassembly.
the harness connections before disassembly.
When disconnecting the connector, hold the connector housing and plug and unlock the
When disconnecting the connector, hold the connector housing and plug and
connector. Holding the case may cause damage to the inside card, while holding the
connector. Holding the case may cause damage to
cable may cause wire breakage.
cable may cause wire breakage.
If the high-power cable terminals of the battery-operated vehicle are not tightened
If the high-power cable terminals of the battery-operated vehicle are
properly, the increased contact resistance causes excessive heat generation, and can
properly, the increased contact resistance causes excessive heat generation, and can
even cause a fire. To
even cause a fire. To prevent accidents and equipment problems, check the tightening
prevent accidents and equipment problems, check the tightening
torque of the high-power cable terminals regularly. Do not pull
torque of the high-power cable terminals regularly. Do not pull the cables to check
connections or during adjustment. If the cable terminal sections are moved,
connections or during adjustment. If the cable terminal sections are moved, re-tighten
the connections.
the connections.
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
Power Controller
Controller
ucks, stackers and low level order
following functions:
AC motors
protected) drives for electric brake coil
link (internal connectors) or CAN bus (external
inputs CANL and CANH
asynchronous 3-phase motors plus a chopper for
us 3-phase motors plus a chopper for DC series
connectors
CAUTION
CAUTION
key switch to the OFF position,
the inside card, while holding the
95 (244)
95 (244)
Service Manual
Service
Manual
5 kW
DC series
position,
unlock the
not tightened
the cables to check
re-tighten
Advertisement
Table of Contents
