Table of Contents
Advertisement
© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
CODE
CODE
200
200
201
201
202
202
203
203
204
204
rights reserved.
rights
reserved.
Revision: B
Revision: B
PBV20N2
PBV20N2
TRUCKTOOL
TRUCKTOOL
AND
AND
DISPLAY
DISPLAY
Waiting for valid PIN code
Waiting for valid PIN code
WAITING FOR PIN
WAITING FOR PIN
This warning indicates that the controller is
This warning indicates that the controller is waiting for a valid PIN
that does not use PIN code lock, check that the PIN CODE LOCK parameter is set to ABSENT.
that does not use PIN
code lock, check that the PIN CODE LOCK parameter is set to ABSENT.
This warning should occur only if the
This warning should occur only if the truck is equipped with a PIN
Accelerator teach mo
Accelerator teach mode
de
LEVER TEACH IN
LEVER TEACH IN
This alarm indicates that the controller entered
This alarm indicates that the controller entered the throttle lever teaching mode. It
as soon as the teaching of the throttle lever is finished.
as soon as the teaching of the throttle lever is finished.
Lift cutout timer active
Lift cutout timer active
LIFT TIMEOUT
LIFT TIMEOUT
This warning is displayed when the lifting
This warning is displayed when the lifting cut off timer has expired (the default
seconds).
seconds).
In case of this warning, release the lift button. If the lift buttons are released and the
In case of this warning, release the lift button. If the lift buttons are released and the warning
persists: check the following:
persists: check the following:
The lift inputs are correct in
The lift inputs are correct in the tester menu.
•
•
Operation of the tiller and the lift buttons is correct.
Operation of the tiller and the lift buttons is correct.
•
•
There are no short circuits in the lift button wirings.
There are no short circuits in the lift button wirings.
•
•
Pump voltage error
Pump voltage error
PUMP VMN NOT OK
PUMP VMN NOT OK
Cause 1: At startup
Cause 1: At startup
The software checks the voltage on the –P
The software checks the voltage on the –P terminal and expects it to remain at
This alarm occurs if the value does not
This alarm occurs if the value does not remain steady.
Cause 2: During operation
Cause 2: During operation
If this alarm is displayed during operation, it indicates that the voltage on the –P terminal is too
If this alarm is displayed during operation, it indicates that the voltage on the –P terminal is too
low when the main contactor is closed.
low when the main contactor is closed.
The software waits for 30 seconds before displaying this alarm, because there are situations
The software waits for 30 seconds before displaying this alarm,
where the pump motor can rotate
where the pump motor can rotate while the –P output is
During this time, it shows the WAIT MOT P STILL warning.
During this time, it shows the
In case of this alarm, check the following:
In case of this alarm, check the
Pump motor internal connections
Pump motor internal connections
•
•
Pump motor power cable
Pump motor power cable connections
•
•
Pump motor leakage to the truck frame
Pump motor leakage to the truck frame
•
•
If the pump motor connections are OK, the
If the pump motor connections are OK, the problem is in the COMBIACX controller.
Pump voltage warning
Pump voltage warning
WAIT MOT.P STILL
WAIT MOT.P STILL
See the description of the alarm 203 PUMP VMN NOT OK.
See the description of the
alarm 203 PUMP VMN NOT OK.
https://www.forkliftpdfmanuals.com/
Document ID: 615023
Document ID: 615023
DESCRIPTION
DESCRIPTION
(Warning)
(Warning)
waiting for a valid PIN code. If it occurs in a
truck is equipped with a PIN code lock.
(Alarm)
(Alarm)
the throttle lever teaching mode. It disappears
(Warning)
(Warning)
cut off timer has expired (the default value is seven
the tester menu.
(Alarm)
(Alarm)
terminal and expects it to remain at a steady value.
remain steady.
while the –P output is not activated (pump deceleration).
WAIT MOT P STILL warning.
following:
connections
problem is in the COMBIACX controller.
(Warning)
(Warning)
163 (244)
163 (244)
Service Manual
Service
Manual
code. If it occurs in a truck
code lock.
disappears
value is seven
warning
Stored
Stored
a steady value.
because there are situations
not activated (pump deceleration).
truck
Advertisement
Table of Contents
