Wlan Basic Settings - Lenze i55AE125B Manual

11.3.2

WLAN basic settings

The WLAN functionality can be configured via the following parameters.
Preconditions
WLAN module has been plugged onto the interface X16 on the front of the inverter.
Details
The WLAN module can be connected and removed during operation.
•
The WLAN module can either create an own WLAN network (access point mode, default
•
setting) or implement itself as a WLAN client in an already existing WLAN network. For
details see the following subchapters.
The WLAN connection is encrypted. The WLAN encryption can be selected in 0x2441:009.
•
0x2441:012 can be used to set that the name of the WLAN network, called SSID, is not
•
visible for other WLAN devices. As a result, the number of WLAN networks displayed on
smartphone or PC can be reduced.
Two data sources are possible for the WLAN settings: Inverter and WLAN module.
•
Data source - inverter: The WLAN settings saved in the inverter are used. Each inverter
•
has its own WLAN settings.
Data source - WLAN module: The WLAN settings saved in the WLAN module are used.
•
In this "stand-alone" mode, the WLAN module can be plugged onto another inverter
and then be used with the same settings (irrespective of the WLAN settings of the
inverter).
The data source is activated with 0x2440.
•
The currently active data source is displayed in 0x2442:004.
•
Parameter Name / value range / [default setting]
0x2440 Initiate WLAN
• From version 02.00
0 No action/no error
1 Restart with current values
version 04.00)
2 Restart with default values
11 Save settings in WLAN module
0x2441:004 WLAN settings: DHCP
• From version 02.00
0 Disabled
1 Enabled
0x2441:005 WLAN settings: DHCP start address
0 ... [0] ... 4294967295
• From version 02.00
0x2441:006 WLAN settings: WLAN operation mode
• From version 02.00
0 Access point mode
1 Client mode
Info
Restart WLAN network with default setting or current settings.
Only status display.
Restart WLAN network with current settings of the WLAN parameters.
(from
• The WLAN settings of the active data source (inverter or WLAN mod-
ule) are used.
• The active data source is displayed in 0x2442:004.
• The data source is not changed by this selection.
Note!
This selection is currently not supported by the WLAN module V1.0.
Restart WLAN network with default setting of the WLAN parameters.
• The WLAN settings saved in the WLAN module are deleted.
• Active data source for the WLAN settings is now the inverter.
Restart WLAN network with current settings of the WLAN parameters.
• The current settings are saved in the WLAN module.
• Active data source for the WLAN settings is now the WLAN module.
1 = Dynamic Host Configuration Protocol (DHCP) is enabled.
• In the access point mode, the DHCP server of the WLAN module is
activated.
• In the client mode, the DHCP-client function is activated.
Definition of the start address when the Dynamic Host Configuration
Protocol (DHCP) is used.
• Only relevant for access point mode.
• When 0 is set, the active IP address + 1 is used as start address.
Definition of the operating mode of the WLAN module.
For a direct connection to another WLAN device, the WLAN module cre-
ates an own WLAN network.
4WLAN access point mode
The WLAN module can be integrated as WLAN client into an already
existing WLAN network.
4WLAN client mode
Additional functions
Wireless LAN (WLAN)
WLAN basic settings
^ 430
^ 435
427