Yamaha RIVAGE PM10 Operation Manual page 371

Messages
Message
Mixing data corrupt on Editor! The internal data of Editor is corrupt.
To recover, go to DEVICE SYNC screen To recover the data, access the DEVICE SYNC screen, and then re-
sync data in the EDITOR → DSP sync direction.
and re-sync data (EDITOR --> DSP).
Multiple DSP engines that are assigned as the word clock master
Multiple word clock masters found! have been detected. Assign the word clock master to only one
unit in the system.
The internal battery of the console is exhausted. The internal
No Battery! (Console) clock cannot keep the correct time. Please contact your Yamaha
dealer for information regarding battery replacement.
The DSP engine's internal battery is exhausted. The internal clock
No Battery! (DSP Engine) cannot keep the correct time. Please contact your Yamaha dealer
for information regarding battery replacement.
The Update function is not available because there is no scene.
No scene to update. Store scene first.
Store a scene first.
Offset values can be edited only when You can set the Overlay offset values only when Overlay is turned
OVERLAY is ON on.
Only one DCA can be rolled out at one You cannot roll-out DCA members on multiple bays
time. simultaneously.
Overlay turned off. Overlay has been turned off.
Overlay turned on. Overlay has been turned on.
Page bookmarked The page is bookmarked.
One of the two power supply units failed to supply power. "X"
Power loss to PSU detected (CS X) represents the power supply unit (A or B) for which power failure
was detected.
The page cannot be displayed because the same page is already
Same page is already open
open on another screen.
Saving aborted The file save operation was interrupted.
The scene renumbering operation cannot be completed because
Scene #XX already exists
a scene number that already exists was specified.
Scene #XX is empty! A scene you tried to recall does not exist.
The scene is protected, and your operation (for example, delete)
Scene #XX is protected!
cannot be completed.
Scene delete undone The scene delete operation was undone.
Scene duplicate undone The scene copy operation was undone.
Scene recall undone The scene recall operation was undone.
Scene store undone The scene store operation was undone.
Screen captured A screen has been captured.
Software control for this card is disabled. This card is not working properly. Check the card's
Check the card's DIP SW setting. DIP switch setting.
Meaning
371
Message
Software exception detected! Restart this An abnormality occurred in software. Restart this control surface
console as soon as possible. immediately.
Software exception detected! Restart this
An abnormality occurred in software. Restart Editor immediately.
editor as soon as possible.
Song file not found! The song file to play cannot be found.
The digital input signal at the [XX] connector is not syncing with
Sync error! [XX] the master clock. Make sure that the input signal is syncing with
the master clock. Otherwise, noise may be heard.
Temporary channel link released A temporary channel link was released.
This device is currently online and cannot This device is currently on-line. You cannot change the device
be changed. type.
This feature is not available in editor
This feature is not available in Editor.
software
This feature will be supported in a future
This feature will be supported in a future software update.
software release.
You cannot modify this item.
This item is read only! This message appears if you attempt to change a Factory preset
title.
Too many Monitor Sources! Max. 8 Too many sources have been selected for monitor input. (Up to
sources can be assigned. eight sources can be assigned.)
Normal operation is not possible because the power at the MY
slots exceeds the maximum power allowed. Remove the MY
cards from unit XX. For information on the maximum number of
Total MY slot power capability exceeded!
MY cards that can be used, please visit the Yamaha Pro Audio
Remove cards from unit XX
website at:
http://www.yamahaproaudio.com/
TWINLANe total cable length too long (HY The total length of cables on the TWINLANe network (HY slot X)
SLOT X) is too long.
The TWINLANe clock master cannot be found. One DSP engine
TWINLANe clock master not found!
in the system must be assigned as the word clock master.
The power of the optical receiver for communication on the
TWINLANe optical receiver input power
TWINLANe network is getting low. Check the cable integrity and
margin low [XXX]
connection, and clean the connection.
TWINLANe: ring connection open! [XXX] The system detected disconnection of the ring connection on the
Check cable connection. TWINLANe network. Check the cable integrity and connection.
The system detected an incorrect TWINLANe cable connection.
TWINLANe: wrong cable connection! Make sure that the ring connection is proper by connecting the
cables in the order of IN-OUT-IN-OUT.
Unassigned encoder You operated an encoder for which no function is assigned.
An unsupported file format was detected and the file failed to
Unsupported file format!
load.
Unsupported USB storage format! The USB storage format is incorrect or unsupported.
CONTENTS FUNCTION MAP
Meaning
RIVAGE PM10 Operation Manual