Yamaha RIVAGE PM10 Operation Manual page 32

Cue
Cue
In order to check the sound of a selected individual channel or DCA, you can output it to
MONITOR OUT, CUE OUT, or PHONES OUT for auditioning.
The RIVAGE PM10 system provides two cue outputs, CUE A and CUE B.
CUE A/B
L R
1 PRE DELAY 3 POST DELAY
(CUE) (CUE)
CUE TRIM
DELAY
STEREO
L
MIX
MONITOR DIMMER
R
MATRIX
SOURCE
ON CUE
TALKBACK
SELECT C
INPUT CH
(DIRECT OUT)
OSC
PRE DELAY POST DELAY
(MONITOR) (MONITOR)
CUE
PRE DELAY
POST DELAY
MONITOR
PRE DELAY
POST DELAY
Number of systems
The RIVAGE PM10 features two cue outputs: CUE A and CUE B.
Structure of the cue circuit
The cue circuit is stereo, with an L-channel and R-channel.
1 CUE TRIM
INPUT CUE/OUTPUT CUE specify the monitor level when PFL is selected.
DCA CUE specifies the monitor level when DCA is cued. DCA UNITY lets you monitor each
DCA at unity gain (the same level as when the DCA fader is set to 0 dB).
INSERT
PLUG-IN
INSERT
4
2 PRE EQ 5 POST EQ 6
(CUE)
(CUE)
DIMMER
CUE OUT
CUE PEQ ON LEVEL
MODE
TALKBACK
CUE SOLO LOGIC
DIMMER/
MONITOR
MONITOR
DIMMER
LEVEL
OUT
PEQ
ON
MODE
TALKBACK
PHONES A-B
L
L R+C PHONES
DA
R
DOWN- LEVEL
MIX LINK
C
CUE/SOLO
LOGIC
INSERT 4
2 CUE OUT MODE
Downmixes the L/R signals to monaural.
3 DELAY
Allows you to delay the cue signal. You can specify up to 1000 msec.
4 INSERT
A plug-in, GEQ, or PEQ can be inserted. This is a single insert point which is fixed at PRE EQ
(immediately before the EQ).
5 PEQ
A dedicated 8-band parametric EQ for the cue is provided.
7
6 CUE LEVEL
This adjusts the output level of the CUE channel. The CUE level can also be assigned to a fader.
L
7 Output structure
R
• L-channel and R-channel of CUE A
• L-channel and R-channel of CUE B
L
R
CUE MODE
C
You can select either MIX CUE or LAST CUE as the cue mode.
MIX CUE: All selected channels will be mixed and auditioned.
LAST CUE: Only most recently selected channel will be auditioned.
CUE stack
Cue signals are divided into four groups: INPUT CUE group, DCA CUE group, OUTPUT CUE
Tip
group, and other CUE group.
Ring
The illustration on the right shows the priority of
Sleeve
the [CUE] keys.
PHONES
LEVEL After you have switched groups from lower to upper
levels, if you then defeat cue for the upper group,
the previous [CUE] key status of the group
immediately below will be restored. For example, if
you switch groups in the order of OUTPUT CUE
group → DCA CUE group → INPUT CUE group →
Other CUE group, you can then successively defeat
the [CUE] keys (CUE/KEY IN CUE buttons) to
successively restore the [CUE] key status of the
previously-selected group.
CUE/SEL LINK
The [SEL] keys can be linked to the [CUE] key that is pressed. For more information, refer to Part 2.
32
CONTENTS
Other CUE group
INPUT CUE group
DCA CUE group
OUTPUT CUE group
RIVAGE PM10 Operation Manual