Buc Parameters (L-Band Device) - Comtech EF Data CDM-625A Installation And Operation Manual

CDM-625A Advanced Satellite Modem
Serial-based Remote Product Management
8.5.8

BUC Parameters (L-Band Device)

Command
Number of
Parameter (Instruction
Arguments
& Qualifier)
BUC BPS= 1 byte, 0 or 1
Power Supply Exception –
enable 600L fn:
ODP=
BUC BFR= 1 byte
10 MHz Exception –
Reference 600L Emulation:
ODR=
BUC BCL= 4 bytes
Current Exception –
Low Limit 600L Emulation:
ODL=
BUC BCH= 4 bytes
Current Exception –
High Limit 600L Emulation:
ODH=
BUC BAD= 1 byte, 1 thru
Address Exception – 15
600L Emulation:
OAD=
BUC BOE= 1 byte, 0 or 1
Output Power Exception –
Enable 600L Emulation:
OOP=
BUC N/A 4 bytes
DC
Current
BUC N/A 4 bytes
Voltage
BUC N/A 4 bytes
Output Power
Level
Command or Query.
Sets or returns BUC Power Supply control in the form x. where:
0=Disable the BUC DC Power Supply
1=Enable the BUC DC Power Supply
Command or Query.
Sets or returns BUC !0 MHz Reference the form x, where:
0=OFF
1=ON
Command or Query.
Sets or returns BUC Current Low Limit, in the form xxxx, where:
xxxx=Value, in 100 mA increments, from 0000 thru 4000 mA
Command or Query.
Sets or returns BUC Current High Limit, in the form xxxx, where:
xxxx=Value, in 100 mA increments, from 0000 thru 4000 mA
Command or Query.
Sets or returns BUC Address in the form xx, where:
xx=Value 01-15.
NOTE: This command is only valid when the FSK is enabled.
Command or Query.
Sets or returns BUC Tx Carrier Output Power function in the form x, where:
0=OFF
1=ON
NOTE: This command is only valid when the FSK is enabled.
Query only.
Returns BUC DC current in the form xxxx, where:
xxxx=Value, in mA, from 0000 and 9999.
NOTE: If not available, response is 0000.
Query only.
Returns BUC Voltage in the form xx.x, where:
xx.x=Value, in volts, from 00.0 thru 64.0
Query only.
Returns BUC Output Power Level in the form xx.x, where:
xx.x=Value, in dBm.
NOTE: Returns xxxx when FSK is not enabled.
EXAMPLE: <0/BOL? >0000/BOL=37.4
Description of Arguments
8–59
MN-CDM625A
Revision 4
Query
Response to
(Instruction & Response to Query
Command
Qualifier)
BPS= BPS? BPS=x
BPS? Exception – (see Description of
BPS* 600L Emulation: Arguments)
BPS# ODP?
BFR= BFR? BFR=x
BFR? Exception – (see Description of
BFR* 600L Emulation: Arguments)
BFR# ODR?
BCL= BCL? BCL=xxxx
BCL? Exception – (see Description of
BCL* 600L Emulation: Arguments)
BCL# ODL?
BCH= BCH? BCH=xxxx
BCH? Exception – (see Description of
BCH* 600L Emulation: Arguments)
BCH# ODH?
BAD= BAD? BAD=xx
BAD? Exception – (see Description of
BAD* 600L Emulation: Arguments)
BAD# OAD?
BOE= BOE? BOE=x
BOE? Exception – (see Description of
BOE* 600L Emulation: Arguments)
BOE# OOP?
N/A BDC? BDC=xxxx
Exception –
(see Description of
600L Emulation: Arguments)
ODC?
N/A BDV? BDV=xx.x
Exception – (see Description of
600L Emulation: Arguments)
ODV?
N/A BOL? BOL=xx.x
Exception – (see Description of
600L Emulation: Arguments)
OOL?