Buc Parameters (L-Band Device) - Comtech EF Data CDM-625A Installation And Operation Manual

CDM-625A Advanced Satellite Modem
Serial-based Remote Product Management
8.5.8

BUC Parameters (L-Band Device)

Command
Parameter Number of
(Instruction
Type Arguments
& Qualifier)
BUC BPS= 1 byte, value of
Power Supply Exception – 0 or 1
enable 600L Emulation:
ODP=
BUC BFR= 1 byte
10 MHz Exception –
Reference 600L Emulation:
ODR=
BUC BCL= 4 bytes
Current Exception –
Low Limit 600L Emulation:
ODL=
BUC BCH= 4 bytes
Current Exception –
High Limit 600L Emulation:
ODH=
BUC BAD= 1 byte, value of
Address Exception – 1 to 15
600L Emulation:
OAD=
BUC BOE= 1 byte, value of
Output Power Exception – 0 or 1
Enable 600L Emulation:
OOP=
BUC N/A 4 bytes
DC
Current
BUC N/A 4 bytes
Voltage
BUC N/A 4 bytes
Output Power
Level
Command or Query.
BUC Power Supply control in the form x. where:
0 = Disable the BUC DC Power Supply
1 = Enable the BUC DC Power Supply
Command or Query.
In the form x, where:
0 = OFF
1 = ON
Command or Query.
BUC Current Low Limit, in the form xxxx, where xxxx is a value between 0 and 4000mA, in 100mA increments.
Command or Query.
BUC Current High Limit, in the form xxxx, where xxxx is a value between 0 and 4000mA, in 100mA increments.
Command or Query.
BUC Address, in the form xx, where xx is a value between 1 and 15.
Note: This command is only valid when the FSK is enabled.
Command or Query.
BUC Tx Carrier Output Power Enable in the form x, where:
0 = OFF
1 = ON
Note: This command is only valid when the FSK is enabled.
Query only.
BUC DC current, in the form xxxx, where xxxx is a value between 0 and 9999, units mA.
If not available, response is 0000.
Query only.
BUC Voltage, in the form xx.x, where xx.x is a value between 0 and 64.0, units in volts.
Query only.
BUC Output Power Level, in the form xx.x, where xx.x is the value in dBm.
Returns xxxx when FSK is not enabled.
Example: BOL=37.4
Description of Arguments
8–56
Revision 0
MN-CDM625A
Query
Response to
(Instruction & Response to Query
Command
Qualifier)
BPS= BPS? BPS=x
BPS? Exception – (see Description of
BPS* 600L Emulation: Arguments)
BPS# ODP?
BFR= BFR? BFR=x
BFR? Exception – (see Description of
BFR* 600L Emulation: Arguments)
BFR# ODR?
BCL= BCL? BCL=xxxx
BCL? Exception – (see Description of
BCL* 600L Emulation: Arguments)
BCL# ODL?
BCH= BCH? BCH=xxxx
BCH? Exception – (see Description of
BCH* 600L Emulation: Arguments)
BCH# ODH?
BAD= BAD? BAD=xx
BAD? Exception – (see Description of
BAD* 600L Emulation: Arguments)
BAD# OAD?
BOE= BOE? BOE=x
BOE? Exception – (see Description of
BOE* 600L Emulation: Arguments)
BOE# OOP?
N/A BDC? BDC=xxxx
Exception –
(see Description of
600L Emulation: Arguments)
ODC?
N/A BDV? BDV=xx.x
Exception – (see Description of
600L Emulation: Arguments)
ODV?
N/A BOL? BOL=xx.x
Exception – (see Description of
600L Emulation: Arguments)
OOL?