Subaru IMPREZA 2002 Service Manual page 387

DIAGNOSTICS FOR ENGINE STARTING FAILURE
ENGINE (DIAGNOSTICS)
Step
CHECK GROUND CIRCUIT OF ECM.
1)Disconnect the connector from ECM.
2)Measure the resistance of harness between
ECM and chassis ground.
Connector & terminal
(8136)
No.
21
-
Chassis ground:
(8136)
No.
22
-
Chassis ground:
(8134)
No.
27- Chassis ground:
(8134)
No.
8
-
Chassis ground:
(8134)
No.
7
-
Chassis ground:
(8134)
No.
34
-
Chassis ground:
(8134)
No.
35
-
Chassis ground:
(8135) No. 25
-
Chassis ground: (MT
vehicle)
1
CHECK INPUT VOLTAGE OF ECM.
Measure the voltage between ECM connector
and chassis ground.
Connector & terminal
(8136) No. 9 (+)
-
Chassis ground (-):
I CHECK INPUT VOLTAGE
OF
ECM.
1)Turn the ignition switch to ON.
2)Measure the voltage between ECM connec-
tor and chassis ground.
Connector & terminal
(8135)
No.
7 (+)
-
Chassis ground ( - ) :
1
CHECK HARNESS BETWEEN ECM AND
MAIN RELAY CONNECTOR.
1)Turn the ignition switch to
OFF.
2)Measure the resistance between ECM and
chassis ground.
Connector & terminal
(8135)
No.
19
-
Chassis ground:
CHECK OUTPUT VOLTAGE FROM ECM.
1)Connect the connector to ECM.
2)Turn the ignition switch to ON.
3)Measure the voltage between ECM connec-
tor and chassis ground.
i
Connector & terminal
(8 135) No. 19 (+)
-
Chassis ground (-):
CHECK INPUT VOLTAGE OF MAIN RELAY.
Check the voltage between main relay connec-
tor and chassis ground.
I
Connector & terminal
(847)
No.
2 (+)
-
Chassis ground (-):
)
CHECK GROUND CIRCUIT OF MAIN RE-
LAY.
1)Turn the ignition switch to OFF.
2)Measure the resistance between main relay
connector and chassis ground.
Connector & terminal
(847) No. 1
-
Chassis ground:
CHECK INPUT VOLTAGE OF MAIN RELAY.
Measure the voltage between main relay con-
nector and chassis ground.
Connector & terminal
(847)
No.
5 (+)
-
Chassis ground (-):
(847)
No.
6 (+)
-
Chassis ground (-):
Check
s the resistance less than 5
n?
s the voltage more than 10 V?
s the voltage more than 10 V?
Is the resistance more than 1
MR?
Is the voltage more than
10 V?
Is the voltage more than 10 V?
Is the resistance less than 5
R?
Is the voltage more than 10 V?
Yes
30 to step 3 .
30 to step 4.
30 to step 5.
30 to step
6.
30 to step 7.
30 to step 8.
20 to step 9.
So to step 10.
No
Repair open circuit
n harness
2etween ECM
:onnector and
mgine grounding
terminal.
Repair open or
around short cir-
x i t of power sup-
~ l y circuit.
Repair open or
around short cir-
wit of power sup-
2ly circuit.
Repair ground
short circuit in har-
ness between
ECM connector
and main relay
connector, then
replace the ECM.
Replace the ECM.
Repair open circuit
in harness
between ECM
connector and
main relay connec.
tor.
Repair open circuit
between main
relay and chassis
ground.
Repair open or
ground short cir-
cuit in harness of
power supply cir-
cuit.
EN(S0HC)-63