Iq9 Skew/Misregistration Rap - Xerox DocuColor 2240 Service Manual

IQ9 Skew/Misregistration RAP

This RAP is used when Skew, System Registration, or Magnification are out of specification.
For Color-to-Color-Misregistration, go to the
Initial Actions
Load some new, dry 24 lb. 11X17/A3 Xerox COLOR Xpressions (NASG), or 90 GSM Colortech
+ (ESG) into each paper tray (use 8.5X11/A4 in Tray 1). Make 3 full color copies from each
paper tray. Mark the appropriate paper tray on these copies.
Procedure
The problem is still present when using the proper paper.
Y N
Explain to the customer that new, dry, 24 lb. Xerox COLOR Xpressions (NASG), or 90
GSM Colortech + (ESG) paper is the specified paper for use in the DocuColor 3535/1632/
2240, WC M24.
The problem occurs only in the printer mode.
Y N
The defect occurs when the document is manually registered on the platen glass.
Y N
Ensure that the Document Transport Belt is clean. Check the Document Handler
Adjustments (ADJ 5.1 through ADJ
drive rolls and pinch rolls for wear or glossing.
The problem is Skew
Y N
The problem is Misregistration
Y N
Adjust the IIT Vertical/Horizontal Magnification
Edge/Side Edge Registration
Enter dC612. Select Pattern 3. Misregistration is present on the copy
Y N
Adjust the IOT Lead Edge/Side Edge Registration
Edge and Side Edge Registration
The defect occurred on copies from all five paper trays.
Y N
Check the IOT Lead Edge/Side Edge Registration
Check the feeder for the affected tray for wear, slipping, damage, or contami-
nation.
• Tray 1 Feeder (PL 2.4)
• Tray 2 Feeder (PL 16.7)
• Tray 3 Feeder (PL 16.9)
• Tray 4 Feeder (PL 16.11)
• Tray 5 Feed Assembly
Registration varies from copy to copy.
A B
Initial issue
DC 3535/2240/1632, WC M24
IQ8 RAP.
5.7). If the problem continues, check the DADF
(ADJ 9.12) and the IOT Lead
(ADJ 9.9).
(ADJ 9.9), then the IIT Lead
(ADJ 9.10 and ADJ 9.11).
(ADJ 9.9) for that tray.
(PL 2.14)
A B
Y N
Go to ADJ 9.9, Lead/Side Edge Adjustment.
Check the components in the Registration Transport Assembly
slipping, damage, or contamination. Clean/replace as required
The defect occurred on copies from all five paper trays.
Y N
Check the feeder for the affected tray for wear, slipping, damage, or contamination.
• Tray 1 Feeder (PL 2.4)
• Tray 2 Feeder (PL 16.7)
• Tray 3 Feeder (PL 16.9)
• Tray 4 Feeder (PL 16.11)
• Tray 5 Feed Assembly
Check the IOT Lead Edge/Side Edge Registration
Check the components in the Registration Transport Assembly
(PL 2.8) for wear, slipping, damage, or contamination. Ensure that the Registration Chute
(PL 2.8) is not binding. Clean/replace as required.
The problem occurs on all jobs.
Y N
Have the customer re-evaluate affected jobs and resend.
DC 3535: Refer to the DFE Service Guide.
09/03
3-13
(PL
(PL 2.14)
(ADJ 9.9) for that tray.
(PL 2.6) and Left Cover
Image Quality
2.6) for wear,
IQ9