Xerox DocuColor 2240 Service Manual page 1199

Table 1 Input Component Control Codes
Code Name
009-101 Toner_Y New
009-102 Toner_M New
009-103 Toner_C New
009-104 Toner_K New
009-150 TNR FULL SNR
009-151 #Y_CRU detect
009-152 #M_CRU detect
009-153 #C_CRU detect
009-154 #K_CRU detect
009-200 2nd BTR Retract Sensor
009-201 POB Sensor
009-203 1st BTR Retract Sensor
010-101 Fuser Exit
010-102 Full Paper Stack Sensor
012-100 IOT Regi Clutch
012-101 Compiler Tray Exit Sensor
012-102 Compiler Paper Sensor
012-103 H-Tra Ent. Sensor
012-104 H-Tra Exit Sensor
012-200 Stacker Paper Sensor
012-201 Stacker Height Sensor
012-202 Stacker Upper Limit Sensor
012-204 Stacker Stack A Sensor
012-205 Stacker Stack B Sensor
012-207 Staple Head Home Sensor
012-208 Low Staple Switch
012-209 Staple Ready Sensor
012-210 Eject Clamp Home Sensor
012-211 Set Clamp Home Sensor
012-212 Rear Tamper Home Sensor
012-215 H-Tra IOT Full Paper Sensor No paper. ON = High
012-216 Front Tamper Home Sensor
012-217 Decurler Cam Position Sen-
sor
General Procedures and Information
dC330
Description
CRU Connection of color is open (The CRU in
use is present, or it is not present). Low=new,
High=old
CRU Connection of color is open (The CRU in
use is present, or it is not present). Low=new,
High=old
CRU Connection of color is open (The CRU in
use is present, or it is not present) Low=new,
High=old
CRU Connection of color is open (The CRU in
use is present, or it is not present) Low=new,
High=old
ON = High
CRU is installed
CRU is installed
CRU is installed
CRU is installed
Retraction. ON = Low
Paper detected. ON = Low
Retraction. ON = Low
Paper detected. ON = High
NotFull. ON = Low
Clutch OFF. ON = High
Paper detected. ON = High
Paper detected. ON = High
Paper detected. ON = High
Paper detected. ON = High
Paper detected. ON = High
Higher than the detection surface. ON = High
Upper Limit position. ON = High
Non-transmissive position. ON = High
Non-transmissive position. ON = High
Not at Home position. ON = High
Low Staple. ON = High
Not at Ready position. ON = High
Not at Home Position (Roller is down). ON = High
Not at Home Position (transmissive). ON = High
Home position. ON = High
Home position. ON = High
Not at Home Position (transmissive). ON = High
Table 1 Input Component Control Codes
Code Name
012-224 Stapler Move Sensor
012-225 Stapler Front Corner Sensor Front Corner position. ON = High
012-300 Front Cover Interlock Switch Open. ON = High
012-301 Top Cover Interlock Switch
012-302 Docking Interlock Sensor
012-305 H-Tra Interlock Sensor
Table 2 Output Component Control Codes
Code Name
001-001 Delayed_off
001-003 Flicker
004-001 Steering Motor
004-002 IBT Motor (104mm/
sec.)
004-003 Drum Motor YMC
(104mm/sec.)
004-004 Main Motor
(104mm/sec.)
004-005 Steering Motor
Home Position
004-006 Drum Motor K
(104mm/sec.)
004-007 Main Motor (52mm/
sec.)
004-008 Main Motor (high
speed)
004-009 Drum Motor K
(52mm/sec.)
004-010 Drum Motor K (high
speed)
09/03
6-108
Description
Non-transmissive position. ON = High
Open. ON = High
Docking release. ON = High
Open. ON = High
Description
Delay Relay
Energize triac to switch in Flicker Resistor.
(220VAC - DC3535 only)
Reswitch the Steering Cam to Home posi-
tion once and operate it at half cycle after
that.
Operate with the IBT Assy. removed to pre-
vent Transfer Belt damage.
Remove all Drum Cartridges before ener-
gizing to prevent Belt damage.
Rotate at medium speed. Operate the
motor with the 2nd BTR nipped, or the LH
Cover opened. Otherwise, the 2nd BTR
might damage the belt.
Returns Steering Cam to home position
ON = Low. Operate with the IBT Assy.
removed to prevent Transfer Belt damage.
Remove all Drum Cartridges before ener-
gizing to prevent Belt damage.
Rotate at low speed. Operate the motor
with the 2nd BTR nipped, or the LH Cover
opened. Otherwise, the 2nd BTR might
damage the belt.
Rotate at high speed. Operate the motor
with the 2nd BTR nipped, or the LH Cover
opened. Otherwise, the 2nd BTR might
damage the belt.
Rotate at low speed. Remove all Drum Car-
tridges before energizing to prevent Belt
damage.
Rotate at high speed. Remove all Drum
Cartridges before energizing to prevent
Belt damage.
DC 3535/2240/1632, WC M24
Conflicts
004-005
004-012,
004-013
004-007,
004-008
004-001
004-004,
004-009
004-004,
004-008
004-004,
004-007
004-006,
004-010
004-006,
004-009
Initial issue