Xerox DocuColor 2240 Service Manual page 1120

Chain-Link Name
742-110 Pre-T/A Start Timing TTM-Tray 4 (Half) 37
742-111 Main Feed Start Timing 3TM-Tray 2
(Half)
742-112 Main Feed Start Timing 3TM-Tray 3
(Half)
742-113 Main Feed Start Timing 3TM-Tray 4
(Half)
742-114 Main Feed Start Timing TTM-Tray 3
(Half)
742-115 Main Feed Start Timing TTM-Tray 4
(Half)
742-116 Tray Type selection
742-118 Regi Loop Length Adjust
DC3535 only (Tray 5 Long Document)(104mm/sec.)
742-120 Adjust Lead Regi (104mm/sec.)
DC3535 only (Heavy1)
742-121 Adjust Lead Regi (104mm/sec.)
DC3535 only (Heavy1)
742-122 Adjust Lead Regi (104mm/sec.)
DC3535 only (Heavy1)
742-123 RegiLoop Length Adjust (Duplex
DC3535 only Heavy1) (104mm/sec., 2-sheet feed)
742-124 RegiLoop Length Adjust (Duplex
DC3535 only Heavy1) (104mm/sec., 1-sheet feed)
742-125 T/A Motor2 Off Timing
DC3535 only
742-126 T/A Motor2 Start Timing
DC3535 only
742-127 T/A Motor Off Acceptance
DC3535 only
742-128 Feed Roller Warning
DC3535 only
742-129 Adjust Lead Regi (52mm/sec.)
DC3535 only (Heavy2)
742-130 Adjust Lead Regi (52mm/sec.)
DC3535 only (Heavy2)
Initial issue
DC 3535/2240/1632, WC M24
Table 1 Chain 742
Default Range Description
0~58 Adjusts the Time between Pre-T/A Starts and Standard Signal (IOT) (431~931 msec.) (1bit=4.8924 msec.)
10 0~22 Sets time between Main Feed Start and Pre-T/A (330~830 msec.). (1bit=4.8924 msec.)
10 0~22 Sets time between Main Feed Start and Pre-T/A (570~1070 msec.). (1bit=4.8924 msec.)
10 0~22 Sets time between Main Feed Start and Pre-T/A (810~1310 msec.) (1bit=4.8924 msec.)
10 0~22 Sets time between Main Feed Start and Pre-T/A (780~1280 msec.) (1bit=4.8924 msec.)
10 0~22 Sets time between Main Feed Start and Pre-T/A (1410~1910 msec.) (1bit=4.8924 msec.)
XC=1; 0~2 Set Tray Type to appropriate mkt setting: 0=metric; 1=inch; 2=FX K-size
XE=0
9 0~81 2.4462 msec/bit
22 0~40 Lead Regi adjustment (Heavy1) at 104mm/sec. (0.2544mm/bit)
23 0~40 Lead Regi adjustment (Heavy1) from Tray 5 at 104mm/sec. (0.2544mm/bit)
22 0~40 Lead Regi adjustment (Heavy1) from Duplex at 104mm/sec. (0.2544mm/bit)
39 0~81 RegiLoop adjustment(104mm/sec.) Heavy1 from Dup (Feed length: Letter LEF or smaller) (1bit=2.4462 msec.)
35 0~81 RegiLoop adjustment(104mm/sec.) Heavy1 from Dup (Feed length exceeding LetterLEF)
Regi Sensor On - DUP MOT Step Down start: 86.66msec
53 33~73 T/A Motor Stop timing at TTM #4T/A Roll Pre Feed (10 msec/bit)
110 90~130 T/A Motor Start timing at TTM #4T/A Roll Pre Feed (10 msec/bit)
48 28~68 TTM #4T/A Roll Pre Feed implementation reject/accept (10 msec/bit)
298500 0~1500000 Tray Feed Roller Warning display timing (number of feeds)
20 0~40 Lead Regi adjustment (52mm/sec.) from Tray (Heavy2) (0.2544mm/bit)
41 0~81 RegiLoop adjustment (52mm/sec.) from Tray (Heavy2) (5.025msec/bit)
09/03
6-29
General Procedures and Information
742--xxx Paper Handling NVM List