Xerox DocuColor 2240 Service Manual page 1198

NOTE: When exiting dC330, the machine resets and communication between the PWS and
the machine is momentarily lost. The PWS will reconnect automatically.
Table 1 Input Component Control Codes
Code Name
001-300 INTLK_1
001-301 INTLK_2
001-302 LH LOW I/L SW
001-304 LH 3TM I/L SW
001-306 INTLK_3
004-100 Belt Home Sensor
004-101 Drum Motor YMC Fail Detec-
tion
004-102 Drum Motor K Fail Detection PR (Drum) Motor K Failure. ON = High
004-200 FAN_LOCK_FAIL
005-102 Document Sensor
005-110 Regi Sensor (DADF)
005-115 Exit Sensor
005-119 Dup Sensor
005-150 #1 Size Sensor
005-151 #2 Size Sensor
005-201 Exchange from IISS
005-300 Platen I/L Switch
005-301 Top Cover I/L Switch
006-160 Polygon Motor Ready Signal Regular rotation of Polygon Motor. ON = Low
006-201 Sheet Abort
006-212 IIT Regi Sensor
006-240 DADF Exist
006-251 APS Sensor1
006-253 APS Sensor3
006-272 PM-0
006-281 IPS Fan Fail
006-300 Platen I/L Switch
006-301 Angle Sensor
007-100 Tray 1 Size Switch 1
007-101 Tray 1 Size Switch 2
007-102 Tray 1 Size Switch 3
Initial issue
DC 3535/2240/1632, WC M24
Description
High when Open is detected. ON = High
High when Open is detected. ON = High
High when Open is detected. ON = High
Low when Open is detected. ON = Low
High when Open is detected. ON = High
IBT is not at Home Position. Open circuit. It is
necessary to operate IBT 5V ON. ON = High
PR (Drum) Motor YMC Failure. ON = High
Fan rotation is stopped. ON = Fault
No paper detected by Document Sensor. ON =
High
Paper detected by Regi Sensor. ON = Low
Paper detected by Exit Sensor. ON = Low
Paper detected by Dup Sensor. ON = Low
No paper detected by #1 Size Sensor. ON = High
No paper detected by #2 Size Sensor. ON = High
Document Exchange Instruction. on from IISS.
ON = Low
Platen Cover Open. ON = High
Top Cover Inter Lock Open. ON = High
Document Regist. ON = Low
Deactuation of Regi Sensor. ON = Low
DADF is not installed. ON = High
Document is detected. ON = APS SNR1: Low,
APS. ON = High
Document is detected. ON = APS SNR3: Low,
APS. ON = High
Flash Memory writing is not in progress. ON =
Inside PWBA
High when FAN failure is detected. ON = High
Low when Platen closed. ON = Low
Low when Platen closed. ON = Low
ON = AN value
ON = AN value
ON = AN value
Table 1 Input Component Control Codes
Code Name
007-103 Tray 1 Size Switch 4
007-104 Tray 2 Size Switch 1
007-105 Tray 2 Size Switch 2
007-106 Tray 2 Size Switch 3
007-107 Tray 2 Size Switch 4
007-108 Tray 3 Size Switch 1
007-109 Tray 3 Size Switch 2 (3TM);
Size Switch 3 (TTM)
007-110 Tray 3 Size Switch 3 (3TM
only)
007-111 Tray 3 Size Switch 4 (3TM
only)
007-112 Tray 4 Size Switch 1
007-113 Tray 4 Size Switch 2 (3TM);
Size Switch 3 (TTM)
007-114 Tray 4 Size Switch 3 (3TM
only)
007-115 Tray 4 Size Switch 4 (3TM
only)
007-116 Tray 1 Level Sensor
007-117 Tray 2 Level Sensor
007-118 Tray 3 Level Sensor
007-119 Tray 4 Level Sensor
007-120 Tray 1 No paper Sensor
007-121 Tray 2 No paper Sensor
007-122 Tray 3 No paper Sensor
007-123 Tray 4 No paper Sensor
007-125 Tray 5 No paper Sensor
007-128 Face Up Tray Detect
008-100 #1Feed Out Sensor
008-102 #3Feed Out Sensor
008-103 #4Feed Out Sensor
008-104 Regi Sensor
008-105 Dup Wait Sensor
008-106 T/A Sensor
008-107 TTM Path Sensor1
008-108 TTM Path Sensor2
008-109 OHP Sensor#L
008-110 OHP Sensor#R
008-300 DUP Open Switch
09/03
6-107
Description
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
ON = AN value
Lift Up. ON = High
Lift Up. ON = High
Lift Up. ON = High
Lift Up. ON = High
No paper. ON = High
No paper. ON = High
No paper. ON = High
No paper. ON = High
No paper. ON = High
Low when Tray is installed. ON = Low
Paper detected. ON = High
Paper detected. ON = High
Paper detected. ON = High
No paper -ON = Low
Paper detected. ON = High
Paper detected. ON = High
Paper detected
Paper detected
ON = Low
ON = Low
ON = High
General Procedures and Information
dC330