Xerox DocuColor 2240 Service Manual page 1151

Chain-Link Name
760-069 Skew Alarm threshold
DC3535
760-070 Y-LD light volume at last RegiCon
760-071 M-LD light volume at last RegiCon
760-072 C-LD light volume at last RegiCon
760-073 K-LD light volume at last RegiCon
760-074 Y-XSO after LD light volume change
760-075 M-XSO after LD light volume change
760-076 C-XSO after LD light volume change
760-077 K-XSO after LD light volume change
760-078 Y-XBI after LD light volume change
760-079 M-XBI after LD light volume change
760-080 C-XBI after LD light volume change
760-081 K-XBI after LD light volume change
760-082 Specified LD light quantity [Y]
DC3535
760-083 Specified LD light quantity [M]
DC3535
760-084 Specified LD light quantity [C]
DC3535
760-085 Specified LD light quantity [K]
DC3535
760-090 Frequency of RegiCon implemented at
DC3535 the same time as ProCon
760-091 YSO at Y-165mm/s
DC3535
760-092 YSO at M-165mm/s
DC3535
760-094 YSO at K-165mm/s
DC3535
760-095 Y-X direction speed correction amount
DC3535
760-096 M-X direction speed correction amount 17
DC3535
760-097 C-X direction speed correction amount 16
DC3535
760-098 K-X direction speed correction amount 16
DC3535
760-099 Process speed at last Regi-Con
DC3535
760-100 Y-Y margin speed switch variation
DC3535
General Procedures and Information
760-xxx Regicon NVM List
Table 1 Chain 760
Default Range Description
30 0~255 Threshold of Skew amount; if this value is exceeded, it is registered as a failure. (2µm/bit)
0 0~1023 Laser Diode light quantity when Regi Control is performed.
0 0~1023 Laser Diode light quantity when Regi Control is performed.
0 0~1023 Laser Diode light quantity when Regi Control is performed.
0 0~1023 Laser Diode light quantity when Regi Control is performed.
236 0~472 XSO value after correction based on the Laser Diode light quantity variation
236 0~472 XSO value after correction based on the Laser Diode light quantity variation
236 0~472 XSO value after correction based on the Laser Diode light quantity variation
236 0~472 XSO value after correction based on the Laser Diode light quantity variation
0 0~3 XBI value after correction based on the Laser Diode light quantity variation
0 0~3 XBI value after correction based on the Laser Diode light quantity variation
0 0~3 XBI value after correction based on the Laser Diode light quantity variation
0 0~3 XBI value after correction based on the Laser Diode light quantity variation
0 0~1023 Current Laser Diode light quantity (LD light quantity specified by ROS)
0 0~1023 Current Laser Diode light quantity (LD light quantity specified by ROS)
0 0~1023 Current Laser Diode light quantity (LD light quantity specified by ROS)
0 0~1023 Current Laser Diode light quantity (LD light quantity specified by ROS)
3 0~16 in what cycle RegiCon should be implemented at the same timing as ProCon during job
237 0~474 1 dot
237 0~474 1 dot
237 0~474 1 dot
17 0~32 1/4 dot
0~32 1/4 dot
0~32 1/4 dot
0~32 1/4 dot
0 0~1 0=RegiCon last implemented at 104 or 52mm/s; 1=RegiCon last implemented at 165mm/sec.
156 0~200 (Y margin variation amount when the speed is switched from 104 or 52mm/sec. to 165mm/s)-100, for Yellow
(1 µm/bit)
09/03
6-60
Initial issue
DC 3535/2240/1632, WC M24