Toshiba CTX100-S Programming Manual page 382

Telephone Button Programming
300 Series Programs
Table 13-31 Programs 318~320 (continued)
Button Sequence
318- Data Day1/Day2/
08~10 Night Dst Type
A7' A7 
~ , n,
Data Day1/Day2/
Night Dst DN
C‚yq
n1,
318-11 VMID for DNIS No.
7 C‚yq
, n,
318-12 DNIS Name
A7 ! C‚yq
, n, ,
9D99IDTÃI‚Ã9UHAÃ
318-15
WHD9
A7 $ C‚yq
, n, ,
13-68
Value(s)
n = 1. No Data (default)
2. Dialing Digits
3. DISA
Tƒx…
4. Built-in modem
5. Night Bell
n1 = Up to 32 digits
n = Up to 10 digits
n = Up to 16 digits
C‚yq
n = Digits 0~9, * and #. For a
pause enter Px, where
C‚yq
x=0~9 (seconds), up to 10
characters (default = no
value).
Select the data call Day1 destination type
•
No Data (default), Dialing Digits, DISA, Built-in Modem or Night
Bell
•
No Data – no destination will ring when the line rings into the
system.
•
Dialing Digits – assigns the line to ring the directory number or
access code defined in the "Destination Digits" assignment
• DISA – assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
•
Modem – assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
•
Night Bell – Assigns the line to cause the night relay to pulse
(one-sec.close/3-sec.open)
Enter the Destination Directory Number. Destination DN is only
required if the destination type is "Dialing Digits"
Enter the VM mail box number which should answer calls for this DID/
DNIS number.
This code is only sent if using SMDI VM integration in Program 580,
01. This code will be replaced, after voice mail answers, by the DTMF
code set in Program 318, 15 DID/DNIS DTMF VMID code - if
programmed; therefore, if using Program 318, 15 code, this VMID
code is not necessary.
This mail box number will be sent to voice mail on a DID/DNIS call
that rings directly to voice mail; and, on a direct DID/DNIS call to a DN
that forwards to voice mail before it is answered by the DN.
If a DID/DNIS call is answered by a station and then transferred to a
DN that forwards to voice mail, this mail box number of the DID/DNIS
number, or the forwarding DN's mail box number will be sent to voice
mail per Program 579, 01.
If this VMID code is not set, direct DID/DNIS calls will go to the VM
general greeting and DID/DNIS calls that forward from a DN to VM
will go to the DN's VMID mail box.
This Voice Mail box number is added to SMDI packets of direct and
forwarded DID\DNIS calls to voice mail as explained above.
Enter DNIS Name. DNIS names can be assigned from the CTX
WinAdmin (not from programming phones).
Enter the VM mail box number which should answer calls for this DID/
DNIS number.
This mail box number will be sent to voice mail on a DID/DNIS call
that rings directly to voice mail; and, on a direct DID/DNIS call to a DN
that forwards to voice mail before it is answered by the DN.
If a DID/DNIS call is answered by a station and then transferred to a
DN that forwards to voice mail, the mail box number of the DID/DNIS
number or the forwarding DN's mail box number will be sent to voice
mail per Program 579, 01.
If this VMID code is not set, direct DID/DNIS calls will go to the VM
general greeting and DID/DNIS calls that forward from a DN to VM
will go to the DN's VMID mail box.
This voice mail box number is sent to the VM port, as DTMF digits,
after the VM port answers a DID/DNIS call as explained above.
These digits are sent to the VM port if the CTX is set for SMDI or
DTMF integration in Program 580, 01.
Strata CTX Programming - Part 3: Telephone Button Programming 11/03
Summary