About Parameters - Omron K3HB-H User Manual

Appendices

About Parameters

■ K3HB-X
Power ON
Protect level L p
RUN.PT:
run.pt
RUN/adjustment protect
0
0 to 2
M
<
SET.PT:
set.pt
Setting level protect
1
0 to 2
M
<
WT.PT:
wt.pt
M
Setting change protect
MODE
off
OFF,ON
M
<
ZR.PT:
zr.pt
Forced-zero protect
off
OFF,ON
MM.PT:
mm.pt
MAX/MIN protect
0
0 to 2
Parameter Display
Always displayed regardless of model or settings.
Displayed only for certain models or settings.
Press the @ [LEVEL] key for at least 1 s from any display (except
for the protect level) to return to the first parameter in the RUN or
initial setting level.
A-18
RUN level
Measurement value
L +
M
Comparative set value HH
L E V E L MODE
99999
3 s min.
-19999 to 99999
3 s min. M
<
Measurement value
Measurement stops
Comparative set value H
99999
-19999 to 99999
M
<
Measurement value
L + M
M
MODE Comparative set value L
L E V E L MODE
- 1 9999
-19999 to 99999 Measurement starts
1 s min.
M
<
Measurement value
Comparative set value LL
- 1 9999
-19999 to 99999
1 s min.
L
L E V E L
Adjustment level L a 1 s max.
BANK: Bank
bank
0 to 7
0
* Displayed when bank
selection (bnk-c) is
set to KEY.
M
CMWT:
MODE cmwt
Communications write
off
OFF, ON
*Displayed only for
Communications Units.
Initial setting level
L 0
L
L E V E L in-ta IN-TA: dsp.a2
Input type A
*1
M
<
FRE:
fre
Power frequency
50
50, 60 Hz
M
<
INP.A1:
inp.a 1
out-p
Scaling input value A1
-19,999 to 99,999
nomal
M
M
<
MODE
L
DSP.A1:
dsp.a 1
amoV
L E V E L Scaling display value A1
-19,999 to 99,999
M
<
INP.A2:
inp.a2
Scaling input value A2
-19,999 to 99,999
*1 Refer to the measurement
*2 This is not displayed in the factory default state.
range table on the front
Change the setting level protection to "0".
panel.
L
Password:
L E V E L
1 s min. 0169
Advanced function setting level
L f
init INIT: Set value initialization
OFF, ON
off
M
<
PASS: PASS output change
pass
LL, L, PASS, H, HH, ERR
pass
Communications
M
<
setting level
HYS: Hysteresis
hys
0 to 9,999
1
M
<
OFF-D: Output OFF-delay
0 to 1,999 (100 ms)
SHOT: Shot output
0 to 1,999 (100 ms)
OUT-N:
Output logic
N-O, N-C
O-STP: Output refresh stop
OFF, OUT, ALL
T-ZR: Tare zero
OFF, ON
Z-TRM: Zero-trimming
OFF, ON
HP-F:
Previous average
value comparison
OFF, ON
BNK-C: Bank selection
OFF, KEY, EV
S-TMR:
Startup compensation timer
0.0 to 99.9 s
S.ERR: Input error enable
OFF, OVER, S.ERR
stdby STDBY:
Standby sequence
off
OFF, ON
CMOV:
Move to calibration level
-19,999 to 99,999
DSP.A2:
Scaling display value A2
L
-19,999 to 99,999
L E V E L
M
<
1 s max.
DP: Decimal point position
dp
0 to 4
M
<
OUT-P:
Comparative output pattern
Standard output,
zone output,level output
M
<
AMOV:
Move to advanced
0
function setting level
-19,999 to 99,999
*2
L
L E V E L
1 s max.
Output test level L t
TEST: Test input
test
-19,999 to 99,999
off
L
L E V E L
1 s max.
Displayed only for
L 6 Communications Units.
U-NO:
u-no
Communications
1
Unit No. 0 to 99
M
<
BPS: Baud rate
bps
9.6, 19.2, or
9 6
. 38.4 kbps
M
<
LEN:
len
Data length
7
7 or 8 bits
M
<
SBIT:
M
sbit
Stop bits
MODE
2
1 or 2 bits
M
<
PRTY:
prty
Parity
e en
None, even, or odd
M
<
SDWT:
sdwt
Send wait time
20
0 to 99 ms
L
L E V E L
1 s max.
Displayed for Linear
Linear output level L 5
Output Units only.
LSET.C: Linear
lset c
.
current model
0 to 20 mA,
4-20
4 to 20 mA
M
<
LSET.V: Linear
lset.V
voltage model
1-5 0 to 5 V, 1 to 5 V,
0 to 10 V
M
<
M
LSET.H: Linear
lset.h
MODE
output upper limit
19999 to 99999
M
<
LSET.L: Linear
lset.l
output lower limit
19999 to 99999