Omron K3HB-H User Manual page 213

Appendices
■ K3HB-S
Power ON
Protect level
L p
RUN.PT:
run.pt
RUN/adjustment
0
protect0 to 2
M
<
SET.PT:
set.pt
Setting level protect
1
0 to 2
M
<
WT.PT:
wt.pt
M
Setting change protect
MODE
off OFF,ON
M
<
ZR.PT:
zr.pt
Forced-zero protect
off
OFF,ON
MM.PT:
mm.pt
MAX/MIN protect
0 0 to 2
Parameter Display
Always displayed regardless of model or settings.
Displayed only for certain models or settings.
Press the @ [LEVEL] key for at least 1 s from any display
(except for the protect level) to return to the first
parameter in the RUN or initial setting level.
A-22
RUN level
Measurement value
L +
M
Comparative set value HH
L E V E L MODE 99999
-19999 to 99999
M
3 s min.
<
Measurement value
Measurement stops
Comparative set value H
99999
-19999 to 99999
M
<
L + Measurement value
M M
Comparative set value L
MODE
L E V E L MODE
- 1 9999
-19999 to 99999
Measurement starts
1 s min.
M
<
Measurement value
Comparative set value LL
- 1 9999
-19999 to 99999
L
L E V E L
Adjustment level L a 1 s max.
BANK:
bank
Bank0 to 7
0
* Displayed when bank
selection (bnk-c) is
set to KEY.
M
CMWT:
cmwt
MODE
Communications write
off
OFF, ON
*Displayed only for
Communications Units.
Initial setting level
L 0
L
CAL: Calculation
cal
L E V E L inp.b1
A, B, K-A, A+B, A-B, K-(A+B),
3 s min.
0
B/A 10000, (B/A-1) 10000
x x
M
<
IN-TA: Input type A
in-ta dsp.b1
0 to 20 mA, 4 to 20 mA,
4-20
0 to 5 V, 1 to 5 V, 5 V, 10 V
M
<
INP.A1:
inp.a 1 inp.b2
Scaling input value A1
4.000
-19,999 to 99,999
M
<
DSP.A1:
L
dsp.a 1
dsp.b2
Scaling display value A1
M
L E V E L
4000
-19,999 to 99,999
MODE
1 s min.
M
<
INP.A2:
inp.a2
Scaling input value A2
20.000
-19,999 to 99,999
M
<
DSP.A2:
dsp.a2
Scaling display value A2
20000
-19,999 to 99,999
M
<
IN-TB: Input type B
in-tb
out-p
0 to 20 mA,4 to 20 mA,
4-20
0 to 5 V, 1 to 5 V, 5 V,
M
10 V
<
This is not displayed in the factory default state.
Change the setting level protection to "0".
L
Password:
L E V E L
0169
1 s min.
Advanced function setting level
L f
INIT: Set value initialization
init
OFF, ON
off
M
<
pass PASS: PASS output change
LL, L, PASS, H, HH, ERR
pass
M Communications
<
setting level
hys HYS: Hysteresis
0 to 9,999
1
M
<
OFF-D: Output OFF-delay
0 to 1,999 ms
SHOT: Shot output
0 to 1,999 ms
OUT-N:
Output logic
N-O, N-C
O-STP: Output refresh stop
OFF, OUT, ALL
T-ZR: Tare zero
OFF, ON
Z-TRM: Zero-trimming
OFF, ON
HP-F:
Previous average
value comparison
Linear output level L 5
OFF, ON
BNK-C: Bank selection
OFF, KEY, EV
S-TMR:
Startup compensation timer
0.0 to 99.9 s
S.ERR: Input error enable
OFF, OVER, S.ERR
stdby STDBY:
Standby sequence
off
OFF, ON
CMOV:
Move to calibration level
-19,999 to 99,999
INP.B1:
Scaling input value B1
4.000 L
-19,999 to 99,999
M
L E V E L
<
DSP.B1:
1 s max.
Scaling display value B1
4000
-19,999 to 99,999
M
<
INP.B2:
Scaling input value B2
20.000
-19,999 to 99,999
M
<
DSP.B2:
Scaling display value B2
20000
-19,999 to 99,999
M
<
k K: Constant K
-19,999 to 99,999
0
M
<
DP: Decimal point position
dp
0 to 4
,,.,,,
M
OUT-P:
<
Comparative output pattern
Standard output, zone output,
nomal
level output
M
<
AMOV:
amoV
Move to advanced
function setting level
0
-19,999 to 99,999
L
L E V E L
1 s max.
Output test level
L t
TEST: Test input
test
-19,999 to 99,999
off
L
L E V E L
1 s max.
Displayed only for
L 6 Communications Units.
U-NO:
u-no
Communications
1
Unit No. 0 to 99
M
<
BPS: Baud rate
bps
9.6, 19.2, or
9 6
. 38.4 kbps
M
<
LEN:
len
Data length
7
7 or 8 bits
M
<
SBIT:
M
sbit
Stop bits
MODE
2
1 or 2 bits
M
<
PRTY:
prty
Parity
eVen
None, even, or odd
M
<
SDWT:
sdwt
Send wait time
20
0 to 99 ms
L
L E V E L
1 s max.
Displayed for Linear Output Units
only.
LSET.C: Linear
lset c
.
current model
0 to 20 mA,
4-20
4 to 20 mA
M
<
LSET.V: Linear
lset.V
voltage model
0 to 5 V, 1 to 5 V,
1-5
0 to 10 V
M
<
M
LSET.H: Linear
lset.h
MODE
output upper limit
20.000
19999 to 99999
M
<
LSET.L: Linear
lset.l
output lower limit
4.000
19999 to 99999