Omron K3HB-H User Manual page 215

Appendices
■ K3HB-H
Power ON
Protect level
L p
RUN.PT:
run.pt
RUN/adjustment protect
0
0 to 2
M
<
SET.PT:
set.pt
Setting level protect
1
0 to 2
M
<
WT.PT:
wt.pt
M
Setting change protect
MODE
off
OFF,ON
M
<
MM.PT:
mm.pt
MAX/MIN protect
0
0 to 2
Parameter Display
Always displayed regardless of model or settings.
Displayed only for certain models or settings.
Press the @ [LEVEL] key for at least 1 s from any display (except
for the protect level) to return to the first parameter in the RUN or
initial setting level.
A-24
RUN level
Measurement value
L +
M
Comparative set value HH L E V E L
L E V E L MODE 99999
-19999 to 99999
3 s min.
M
3 s min.
<
Measurement value
Measurement stops
Comparative set value H
99999
-19999 to 99999
M
<
L +
M M Measurement value
MODE Comparative set value L
L E V E L MODE
- 1 9999
-19999 to 99999 Measurement starts
1 s min.
M
<
Measurement value
Comparative set value LL
- 1 9999
L E V E L
-19999 to 99999
1 s min.
L
L E V E L
Adjustment level L a 1 s max.
bank BANK: Bank
0 to 7
0
* Displayed when bank
selection (bnk-c) is
set to KEY.
M
CMWT:
cmwt
MODE
Communications write
off
OFF, ON
*Displayed only for
Communications Units.
Initial setting level L 0
L
IN-TA:
in-ta
Input type A
2-k
*1
M
<
FRE:
fre
Power frequency
50
50, 60 Hz
M
<
D-U:
d-u
Temperature unit
c
C, F
M
<
OUT-P:
M
out-p
L Comparative output pattern
MODE
Standard output, zone
nomal
output, level output
M
<
AMOV:
amoV
Move to advanced
0
function setting level
-19999 to 99999
*2
*1 Refer to the measurement range table
on the front panel.
*2 This is not displayed in the factory default state.
Change the setting level protection to "0".
Password:
L
0169
L E V E L
1 s min.
Advanced function setting level
L f
INIT:
init
Set value initialization
off
OFF, ON
M
<
PASS:
pass
PASS output change
pass
LL, L, PASS, H, HH, ERR
M
Communications
<
HYS: Hysteresis setting level
hys
0 to 9,999
1
OFF-D:
Output OFF-delay
0 to 1,999 (100 ms)
SHOT: Shot output
0 to 1,999 (100 ms)
OUT-N:
Output logic
N-O, N-C
O-STP:
Output refresh stop
OFF, OUT, ALL
HP-F:
Previous average
value comparison
OFF, ON
BNK-C:
Bank selection
OFF, KEY, EV
S-TMR:
Startup compensation timer
Linear output level L 5
0.0 to 99.9 s
S.ERR:
Input error enable
OFF, OVER, S.ERR
STDBY:
stdby
Standby sequence
off
OFF, ON
CJC:
cjc
Cold junction compensation
on
OFF, ON
CMOV:
Move to calibration level
-19,999 to 99,999
L
L E V E L
1 s max.
L
L E V E L
1 s max.
Output test level
L t
test
TEST: Test input
-19,999 to 99,999
off
L
Displayed only
L E V E L
for Communi-
1 s max.
cations Units.
L 6
U-NO:
u-no
Communications
1
Unit No. 0 to 99
M
<
BPS: Baud rate
bps
9.6, 19.2, or
9 6
. 38.4 kbps
M
<
LEN:
len
Data length
7
7 or 8 bits
M
<
SBIT:
M
sbit
Stop bits
MODE
2
1 or 2 bits
M
<
PRTY:
prty
Parity
eVen
None, even, or odd
M
<
SDWT:
sdwt
Send wait time
20
0 to 99 ms
L
L E V E L
1 s max.
Displayed for Linear
Output Units only.
LSET.C: Linear
lset c
.
current model
0 to 20 mA,
4-20
4 to 20 mA
M
<
LSET.V: Linear
lset.V
voltage model
0 to 5 V, 1 to 5 V,
1-5
0 to 10 V
M
<
M
LSET.H: Linear
lset.h
MODE
output upper limit
1300.0
19999 to 99999
M
<
LSET.L: Linear
lset.l
output lower limit
- - 200.0
19999 to 99999