About Parameters - Omron K3HB-C User Manual

About Parameters

■ K3HB-R
Power ON
Protect level
L p
L +
RUN.PT:
run.pt
L E V E L
RUN/adjustment protect
0
0 to 2 3 s min.
M
<
SET.PT:
set.pt
Setting level protect
1
0 to 2
M
L +
<
M
WT.PT:
L E V E L
wt.pt
Setting change protect
1 s min.
off
OFF,ON
M
<
MM.PT:
mm.pt
MAX/MIN protect
0
0 to 2
Parameter Display
:
Always displayed regardless of model or settings.
:
Displayed only for certain models or settings.
Press the @ [LEVEL] key for at least 1 s from
any display (except for the protect level) to
return to the first parameter in the RUN or
initial setting level.
Measurement value
M
Comparative set value HH
MODE
99999
-19999 to 99999
M
<
Measurement value
Comparative set value H
99999
-19999 to 99999
M
<
M
M Measurement value
MODE MODE
Comparative set value L
- 1 9999
-19999 to 99999
M
<
Measurement value
Comparative set value LL
- 1 9999
-19999 to 99999
L
L E V E L
1 s max.
Adjustment level L a
bank BANK: Bank
0 to 7
0
* Displayed when bank
selection (bnk-c) is set
M to KEY.
MODE
cmwt CMWT:
Communications write
off
OFF, ON
*Displayed only for
Communications Units.
Advanced function setting level
Initial setting
level L 0
L
L E V E L
FUNC:
func
3 s min.
Function
f1
F1 to F6
Measurement
M
<
IN-TA:
stops
in-ta
Input type A
No contact (NO/NC)
00
Contact (NO/NC)
M
<
IN-TB:
Measurement
in-tb
Input type B
starts
00
No contact (NO/NC)
M
Contact (NO/NC)
<
L M
MODE
ps.ax PS.AX:
L E V E L
Prescale AX
1 s min.
1.0000
0.0000 to 9.9999
M
<
PS.AY:
ps.ay
Prescale AY
10 0
9 to 9
M
<
* This is not displayed in the factory default state.
Change the setting level protection to "0".
Password:
L
L E V E L
0169
1 s min.
L f
INIT: Set value initialization
init
OFF, ON
off
M
<
pass
PASS: PASS output change LL,
L, PASS, H, HH
pass
M
HYS: Hysteresis
<
0 to 9,999 when TIME is OFF.
hys
0.00.00 to 0.59.59 when TIME is
h:min:s
1
0.00.00 to 59.59.9 when TIME is
M
< min:s:ms
OFF-D: Output OFF-delay 0
to 1,999 ms
SHOT: Shot output 0
to 1,999 ms
OUT-N:
Output de-energization
N-O, N-C
o-stp O-STP: Output refresh stop
OFF, OUT, ALL
off
BNK-C: Bank selection
OFF, KEY, EV
S-TMR:
Startup compensation timer 0.0 to
99.9 s
STDBY:
stdby
Standby sequence
off
OFF, ON

About Parameters

PS.BX:
ps.bx
Prescale BX
L
1.0000
0.0000 to 9.9999
L E V E L
M
1 s max.
<
PS.BY:
ps.by
Prescale BY
10 0
9 to 9
M
<
TIME:
time
OFF, min, h:min:s,
off
min:s, 100 ms
M
<
DP:
dp
Decimal point position
00000
0 to 4
M
<
OUT-P:
out-p
Comparative output
pattern, standard
normal
output, zone output,
M
<
level output
*
amoV
AMOV:
Move to advanced
0
function setting level
19999 to 99999
L
L E V E L
1 s max.
Output test level L t
test TEST: Test input
-19,999 to 99,999
off
L
L E V E L
Displayed only for
1 s max.
Communications
Communications
L 6
Units.
setting level
U-NO:
u-no
Communications
1
Unit No. 0 to 99
M
<
BPS: Baud rate
bps
9.6, 19.2, or
9 . 6
38.4 kbps
M
<
LEN:
len
Data length
7
7 or 8 bits
M
<
SBIT:
M
sbit
Stop bits
MODE
2
1 or 2 bits
M
<
PRTY:
prty
Parity
eVen
None, even, or odd
M
<
sdwt SDWT:
Send wait time
20
0 to 99 ms
L
L E V E L
1 s max.
Displayed for Linear
L 5
Linear output level
Output Units only.
LSET.C: Linear
lset . c
current model
0 to 20 mA,
4-20
4 to 20 mA
M
<
LSET.V: Linear
lset.V
voltage model
1-5 0 to 5 V, 1 to 5 V,
M 0 to 10 V
M
<
MODE
LSET.H: Linear
lset.h
output upper limit
99999
19999 to 99999
M
<
LSET.L: Linear
lset.l
output lower limit
:9999
19999 to 99999
A-23