Omron E5AR - MANUAL 2 User Manual page 342

Move to protect level ...................... 6-26, 7-26
Move to setting area 1 ................... 6-26, 7-26
Movement average enable ..................... 8-50
MV at error ..................................... 5-18, 8-18
MV at stop ............................. 4-27, 5-18, 8-18
MV change rate limit ............................... 5-17
MV change rate limit (cooling) ................ 8-19
MV change rate limit (heating) ................ 8-19
MV change rate limit mode ..................... 8-78
MV display selection ............................... 8-60
MV limit .......................................... 5-16, 8-31
MV monitor (cooling) ............................... 8-10
MV monitor (heating) ................................ 8-9
N
Non-volatile memory error ...................... 10-3
Number of enabled channels .................. 8-70
O
Obtaining input shift values ....................... 5-3
ON/OFF Control ...................................... 4-18
Open/Close hysteresis ................... 3-12, 8-17
Operation adjustment protect ................. 5-24
Operation at potentiometer error ............ 8-79
Operation at potentiometer input error .... 3-12
Operation at power ON .................. 4-27, 8-73
Operation at startup (SP ramp) ................. 5-8
Operation commands
(Communication/CompoWay/F) ............. 6-11
Operation commands
(Communication/Modbus) ....................... 7-14
Operation indicators .................................. 1-5
Operation level .................................8-5, A-11
Operational considerations ..................... 4-32
OUT1 (operation indicator) ....................... 1-5
OUT2 (operation indicator) ....................... 1-5
OUT3 (operation indicator) ....................... 1-5
OUT4 (operation indicator) ....................... 1-5
Output calibration .................................... 9-12
Output state at error ................................ 10-3
Output type ............................................. 4-15
Overlap band ................................... 3-8, 8-15
P
Panel cutout dimensions ........................... 2-2
Part Names and Functions ....................... 1-4
PF key protect ......................................... 5-25
PF settings .............................................. 5-21
PF1 monitor/setting item ......................... 8-69
PF1 setting .............................................. 8-68
PF2 monitor/setting item ......................... 8-69
PF2 setting .............................................. 8-68
PID set auto select data .......................... 8-74
PID set auto select hysteresis ................ 8-74
PID set automatic selection .................... 5-13
PID set automatic selection data ............. 8-74
PID set automatic selection hysteresis ... 8-74
PID Set No. .................................... 5-10, 8-27
PID Set No. Automatic selection range upper
limit .......................................................... 8-32
PID sets ............................................ 1-2, 5-12
PID setting level .............................8-30, A-15
Position proportional control ...................... 3-9
Position proportional dead band .... 3-12, 8-17
Potentiometer input error ........................ 10-3
Potentiometer inputs (terminals) ............. 2-14
Power supply (terminals) ......................... 2-11
Precautions when wiring ......................... 2-11
Proportional band .................................... 8-31
Protect ..................................................... 5-24
Protect key ................................................ 1-6
Protect level .....................................8-3, A-10
Pulling the unit out ..................................... 2-3
PV dead band ................................ 3-12, 8-74
PV decimal point display ......................... 8-39
PV tracking .............................................. 8-76
PV/SP ........................................................ 8-7
"PV/SP" display screen selection ............ 8-60
R
RAM data store .............................. 6-25, 7-25
RAM write mode ...................................... 8-70
Ramp SP monitor ...................................... 8-9
Ratio control ..................................... 1-9, 3-18
Read setting data
(Communication/Modbus) ....................... 7-18
Registering calibration data ....................... 9-4
Remote SP lower limit ............................. 8-38
Remote SP monitor ................................... 8-8
Remote SP upper limit ............................ 8-38
Remote SP/local SP ................................ 8-14
Resistance temperature input sensor calibra-
tion .......................................................... 9-10
Reverse operation ................................... 4-14
Reverse operation (heating) ...................... 1-9
RS-485 .................................................... 2-17
RSP (operation indicator) .......................... 1-5
RSP input error ....................................... 10-3
Run ................................................. 6-21, 7-21
Run/Stop ...............................4-27, 5-30, 8-11
S
Saving setting ............................................ 4-4
Scaling ...................................................... 4-9
Scaling display value ............................... 8-37
Scaling input value .................................. 8-37
Sensor induction noise reduction ............ 8-40
Set values ................................................. 4-4
Setting and changing the SP ................... 4-17
Setting areas ........................................... 6-13
Setting change protect ............................ 5-25