Dip Switch Functions - Toshiba e-STUDIO350 Service Handbook
Multifunctional digital systems
Hide thumbs
Also See for e-STUDIO350:
- Service manual (286 pages) ,
- Operator's manual (162 pages) ,
- Operator's manual (102 pages)
Table of Contents
Advertisement
3.12.7
DIP switch functions
You can simulate various functions by setting the DIP switch (SW1) on the finisher controller PC board
appropriately.
Initiating Operations
1) Remove any obstacles from the area of operation.
2) Set the DIP switch (SW1) as shown, and turn ON the power (so that LED1 will start to blink).
3) Press the pushing switch (SW2) twice to initiate the operation in question. (LED2 will remain on dur-
ing operation).
Setting
Delivery motor
ON
1
2
3
4
5
6
7
8
Stack process-
ON
ing motor (stack
delivery lever)
1
2
3
4
5
6
7
8
Stack process-
ON
ing motor
(returning roller)
1
2
3
4
5
6
7
8
Front jogging
ON
plate motor
1
2
3
4
5
6
7
8
Rear jogging
ON
plate motor
1
2
3
4
5
6
7
8
Upper stack tray
ON
motor (up)
1
2
3
4
5
6
7
8
Upper stack tray
ON
motor (down)
1
2
3
4
5
6
7
8
Lower stack tray
ON
motor (up)
1
2
3
4
5
6
7
8
Lower stack tray
ON
motor (down)
1
2
3
4
5
6
7
8
Stapler motor
ON
1
2
3
4
5
6
7
8
Shipping posi-
ON
tion operation
1
2
3
4
5
6
7
8
Note:
Note:
Perform the shipping position operation when the finisher is packed again.
e-STUDIO350/352/353/450/452/453
ADJUSTMENT
Item
The delivery roller rotates in a specific speed.
The stack delivery lever moves to its home
position and stops.
The returning roller moves to the home posi-
tion and stops.
When not at the
home position
When at the
home position
When not at the
home position
When at the
home position
The upper stack tray moves up and stops
when the upper stack tray upper limit sensor
turns ON.
The upper stack tray moves down and stops
when the lower stack tray lower limit sensor
turns ON.
The lower stack tray moves up and stops
when the lower stack tray upper limit sensor is
turned ON.
The lower stack tray moves down and stops
when the lower stack tray lower limit sensor is
turned ON.
The stapler motor stops after the stapling
operation.
The upper and lower stack trays move to the
shipping position and stop.
3 - 92
Operation
The front jogging plate
moves to its home position
and stops.
The front jogging plate
moves over a specific posi-
tion and stops at the home
position.
The rear jogging plate
moves to the home posi-
tion and stops.
The rear jogging plate
moves over a specific dis-
tance and stops.
© 2003 - 2008 TOSHIBA TEC CORPORATION All rights reserved
To stop
•
Press SW2 again.
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
•
Press SW2 again.
•
Turn OFF the joint
sensor (S4).
•
Press SW2 again.
•
Turn OFF the joint
sensor (S4).
•
Press SW2 again.
•
Turn OFF the joint
sensor (S4).
•
Press SW2 again.
•
Turn OFF the joint
sensor (S4).
•
Press the stapler
safety switch (S14).
•
Turn OFF the joint
sensor (S4).
•
Turn OFF the joint
sensor (S4).
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
