Wds Messages - Allen-Bradley Stratix 5100 User Manual

Appendix C Error and Event Messages
Message
DOT1X-SHIM-3-UNSUPPORTED_KM:
"Unsupported key management: %X."
DPT1X-SHIM-4-PLUMB_KEY_ERR: "Unable to
plumb keys - %s."
DOT1X-SHIM-3-PKT_TX_ERR: "Unable to tx
packet -%s."
DOT1X-SHIM-3-ENCAP_ERR: "Packet encap
failed for %e."
DOT1X-SHIM-3-SUPP_START_FAIL: "Unable to
start supplicant on %s."
DOT1X-SHIM=3-NO_UPLINK: "No uplink found
for %s."
Information Group rad_acct: Radius server
<ip address> is responding again
(previously dead). Error Group acct: No
active radius servers found. Id 106

WDS Messages

Message
WLCCP-WDS-6-REPEATER_STOP: WLCCP WDS on
Repeater unsupported, WDS is disabled.
WLCCP-WDS-6-PREV_VER_AP: A previous
version of AP is detected.
WLCCP-AP-6-INFRA: WLCCP Infrastructure
Authenticated
WLCCP-AP-6-STAND_ALONE: Connection lost
to WLCCP server, changing to Stand-Alone
Mode
WLCCP-AP-6-PREV_VER_WDS: A previous
version of WDS is detected
WLCCP-AP-6-UNSUP_VER_WDS: An unsupported
version of WDS is detected
WLCCP-NM-3-WNM_LINK_DOWN: Link to WNM is
down
WLCCP-NM-6-WNM_LINK_UP: Link to WNM is up
WLCCP-NM-6-RESET: Resetting WLCCP-NM
WLCCP-WDS-3-RECOVER: "%s
590
Explanation
Am error occurred during the initialization of the shim
layer. An unsupported key management type was found.
An unexpected error occurred when the shim layer tried to
plumb the keys.
An unexpected error occurred when the shim layer tried to
transmit the dot1x packet.
An unexpected error occurred when the shim layer tried to
transmit the dot1x packet. The packet encapsulation
failed.
An unexpected error occurred when the shim layer tried to
start the dot1x suppliant on the indicated interface.
While processing a dot1x event or message on a dot11
interface, a situation was encountered where an uplink
was expected, but not found.
This message is seen if the
command is configured on the access
deadtime 10
point.This command is configured to set an interval, the
access point does not attempt to use servers that don't
respond. Thus avoids the time needed to wait for a
request to time out before trying the next configured
server. A Radius server marked as dead is skipped by
additional requests for the duration of the minutes unless
all servers are marked dead. Configuring dead time for 10
minutes means that the server cannot be used for 10
minutes.
Explanation
Repeater access points don't support WDS.
The WDS device detected a previous version of the access
point.
The access point successfully authenticated to the WDS
device.
The access point lost its connection to the WDS device and
is in stand-alone mode.
The access point detected a previous version of WDS.
The access point detected an unsupported version of
WDS.
The network manager is not responding to keep-active
messages.
The network manager is now responding to keep-active
messages.
A change in the network manager IP address or a
temporary out-of-resource state can cause a reset on the
WDS network manager subsystem, but operation returns
to normal shortly.
WDS graceful recovery errors.
Rockwell Automation Publication 1783-UM006A-EN-P - May 2014
Recommended Action
None.
None.
None
None.
None.
None.
You can disable this command if you want
radius-server
this log to disappear. Actually this message is
not really a major problem, it is just an
informational log.
Recommended Action
None.
None.
None.
None.
Check for an unsupported version of WDS on
your network.
Check for an unsupported version of WDS on
your network.
Check for a problem with the network
manager or with the network path to the
network manager.
None.
None.
None.