System Log Messages; 802.11 Subsystem Messages - Allen-Bradley Stratix 5100 User Manual

Appendix C Error and Event Messages

System Log Messages

Table 5 - System Log Messages
Message
%DOT11-4-LOADING_RADIO: Interface [chars],
loading the radio firmware ([chars])
%LINEPROTO-5-UPDOWN: Line protocol on Interface
[chars], changed state to [chars]
%SYS-5-RESTART: System restarted --[chars]
%SYS-5-CONFIG_I: Configured from [chars] by
[chars]
%LINEPROTO-5-UPDOWN: Line protocol on Interface
[chars], changed state to [chars]
%SNMP-5-COLDSTART: SNMP agent on host [chars] is
undergoing a cold start
%SYS-6-CLOCKUPDATE: System clock has been updated
from [chars] to [chars], configured from [chars]
by [chars].

802.11 Subsystem Messages

Table 6 - Subsystem Messages
Message
DOT11-6-FREQ_USED: "Interface %s,
frequency %d selected."
DOT11-4-NO-VALID_INFRA_SSID: "No
infrastructure SSID configured. %s not
started."
DOT11-4-VERSION_UPGRADE: "Interface %d,
upgrading radio firmware."
DOT11-2-VERSION_INVALID: "Interface %d,
unable to find required radio version
%x.%x/ %d/
DOT11-3-RADIO_OVER_TEMPERATURE:
"Interface %s Radio over temperature
detected."
DOT11-6-RADIO_TEMPERATURE_NORMAL:
"Interface %s radio temperature returned
to normal."
DOT11-3-TX_PWR_OUT_OF_RANGE: "Interface
%s Radio transmit power out of range."
DOT11-3-RADIO_RF_LO: "Interface %s Radio
cannot lock RF freq."
DOT11-3-RADIO_IF_LO: "Interface %s Radio
cannot lock IF freq."
DOT11-6-FREQ_SCAN: "Interface %s Scanning
frequencies for %d seconds."
DOT11-2-NO_CHAN_AVAIL: "Interface %s, no
channel available."
584
This table explains the system log messages.
Explanation
The radio has been stopped to load new
firmware.
The data link level line protocol has
changed state.
A reload or restart was requested.
The router configuration has been
changed.
The data link level line protocol has
changed state on the interface shown.
The SNMP server completed a coldstart.
The system clock has been modified.
This table explains the subsystem messages.
Explanation
After scanning for an unused frequency, the indicated
interface selected the displayed frequency.
No infrastructure SSID was configured and the indicated
interface was not started.
When starting the indicated interface, the access point
found the wrong firmware version. The radio is loaded
with the required version.
When trying to upgrade the radio firmware on the
indicated interface, the access point recognized that the
indicated radio firmware packaged with the Cisco IOS
software had the incorrect version.
The radio's internal temperature exceeds maximum limits
on the indicated radio interface.
The radio' s internal temperature has returned to normal
limits on the indicated radio interface.
The transmitter power level is outside the normal range
on the indicated radio interface.
The radio phase lock loop (PLL) circuit is unable to lock the
correct frequency on the indicated interface.
The radio intermediate frequency (IF) PLL is unable to lock
the correct frequency on the indicated interface.
Starting a scan for a least congested frequency on the
interface indicated for a the time period indicated.
No frequency is available, likely because RADAR has been
detected within the previous 30 minutes.
Rockwell Automation Publication 1783-UM006A-EN-P - May 2014
Recommended Action
No action is required.
No action is required.
Notification message only. No action is required.
This is a notification message only. No action is
required.
No action is required.
Notification message only. No action is required.
This is an informational message only. No action
is required.
Recommended Action
None.
Add at least one infrastructure SSID to the
radio configuration.
None.
None.
Take steps necessary to reduce the internal
temperature. These steps vary based on your
specific installation.
None.
Remove unit from the network and service.
Remove unit from network and service.
Remove unit from network and service.
None.
None.